shear rate的例句大全

The new stress rate is applied to a hypoelastic body experiencing simple shear, there is no oscillation in the stresses and the general normal stress-shear stress relation for superelasticity is also satisfied.

用新应力率对次弹性体简单剪切进行了计算，得到的应力不振荡，且满足超弹性正应力-剪应力普适关系。

The shear crack would expand along the shear direction and the tensile crack would expand some distance along the radial direction and then expand along the shear direction in this experimental strain-rate.

在实验加载应变率范围内，剪切裂纹在外壁面萌生后会一直沿剪切方向向内壁面扩展，拉伸裂纹在沿径向扩展一段距离后，转而沿剪切方向扩展。

The experimental results show that 0.2% yield shear stress, ultimate shear stress and 0.2% yield tensile stress, ultimate tensile stress under torsion tension combined high strain rate decrease with increasing temperature.

试验结果表明：该材料在高应变率扭拉复合加载下的名义剪切屈服强度、剪切强度极限和名义拉伸屈服极限、拉伸强度极限均随温度的升高而降低。

The shear strength and elongation of the lap joint increase with the increase of strain rate.

焊点的剪切强度及伸长量随应变速率的增加而增加。

Failure modes of concrete will change from the bending failure to shear failure when the corrosion rate increase. Shear failure is brittle failure, which will injure the performance of structures.

随着锈蚀率的增加，混凝土梁的破坏形态会由弯曲破坏转变为剪切破坏，而剪切破坏为脆性破坏，将严重影响结构的服役安全。

The polymer solution was manifested to show the property of shear thinning at low flow rate and shear thickening if the flow rate exceeded a point.

实验发现聚合物溶液在低流速下，表现剪切变稀，超过一定流速后，表现为剪切增稠。有效粘度和弹性粘度随着剪切速率和疏水基含量的增大而增大。

The rheological investigation indicates that the slurry pumped with SAF is pseudoplastic fluid, has remarkable characteristic of thixotropic property, and the excellent anti-shearing quality of the slurry is proved under the constant shearing rate of 100 s~ (-1).

流变性实验研究发现，浆体属于假塑性流体，具有明显的触变性，并且浆体在100s-1的固定剪切速率下剪切具有较好的抗剪切性。

The distributions of temperature, stress, strain, strain rate, displacement and viscous damping coefficient within ductile shear zone at different time intervals are distinguished in the cases of accelerating creep age and strain softening.

并对加速蠕变和应变软化两种情况，给出了不同时刻韧性剪切带内的温度、应力、应变、应变率、位移和粘滞系数的分布特征，描述了岩石递进变形的规律。

According to the cutting speed, feed rate, sampling frequency and time, the characteristic parameters of saw-tooth chip type and shear instability could be calculated based on the saw-tooth chip forming frequency formula supported by M.C. Shaw theory.

从切削力高频信号的切削速度、进给量、采样频率和时间可以定性描述锯齿形切屑形态和剪切失稳的特征参数，依据Shaw建立的锯齿形生成频率模型。

the change of the entanglement density of polymer melt in oscillatory shear is studied by using liu "s kinetics rate equation. "

采用前人提出的动态速率方程研究振动剪切作用下聚合物熔体缠结密度的变化情况。

reduce time for blade-changing of pendulum shear to increase operation rate

缩短剪刃更换时间提高摆剪作业率

The synthesis method, effect of initiator on the monomer conversion, drag reducing rate of associating DRA and anti-shearing performance were researched.

本文主要合成一种新型抗剪切减阻剂，并对其合成方法、引发剂对聚合单体转化率的影响、缔合减阻剂减阻率及抗剪切性能的比较等进行了实验研究。

The reason for the sawtooth chips is that the adiabatic shear localization occurs in the primary deformation zones when thermal softening exceeds strain and strain rate hardening.

锯齿形切屑产生的原因是第一变形区内因热软化超过应变和应变率强化而发生了绝热剪切局部化。

Finally, the relation among component of shear deformation, component of extension deformation and deformation rate and tectonic earthquake is analyzed on the basis of a example.

最后根据实例计算结果分析了剪切变形分量、扩张变形分量与形变速率、构造地震的关系。

With increasing flow velocity the shear stress on the metal electrode surface and the electrochemical corrosion rate increased, and the electrochemical reaction impedance decreased.

随着流速增大，电极表面受到的切应力增大，反应阻抗减小，电化学腐蚀加速，协同效应增强，结果使电极流动腐蚀速度增加。

Systematic study is done for the strain energy density factor criterion, distortional strain energy density factor criterion, dilatational strain energy density factor criterion, circumferential tensile stress criterion, energy release rate criterion and twin shear stress criterion.

对应变能密度因子准则、形状改变能密度因子准则、体积改变能密度因子准则、能量释放率准则以及最大周向拉应力准则和双剪应力准则进行了系统地研究。

The location of shear strain rate localization coincides in position with the location of volumetric strain rate, which is the actual failure zone of rock.

剪切应变率（或应变）局部化区域与体积应变率（或应变）的位置重合，局部化区域就是岩样最终的破坏位置。

Larger loading rate leads to larger inclination angle of shear band in the middle of specimen.

随着加载速率的增加，岩石中部剪切带的倾角有增大的趋势。

The matrix and fiber are assumed elastic, and the sliding rate is proportional to the shear stress on the interface.

基体和纤维为弹性的，而界面滑动速率正比于界面剪应力。

A constitutive relation between flow shear stress rate and the relative sliding velocity of shear band is also obtained.

推导了剪应力（率）与剪切带相对错距（速度）的本构关系。