sheet structure的例句大全

Zero interest rate commitment, changing the central bank balance sheet structure and scale become the operational methods of the central bank.

零利率政策承诺、改变央行资产负债表结构和规模成为量化宽松货币政策的操作方法。

Crater Distribution on the Rear Wall of Aluminum Dual-sheet Structure under Hypervelocity Normal Impact

铝双层板结构超高速正撞击后板弹坑分布

The outer layer of chicken claw is sheet structure, and the inner layer is amorphous. From outside to inside, the content of sulfur gradually decreases. As a result, the nano-hardness and elastic modulus also decrease.

鸡爪的外层为片状结构，内层为无定形组织，从外层到内层，S含量逐渐降低，纳米硬度和弹性模量也逐渐降低。

Study on β-Sheet Structure Formed by Self-assembly of Fibroin Crystalline Typical Peptides Using Thioflavine T Fluorescence Probe

Thioflavine T荧光探针法研究丝素结晶区典型肽段自聚集的β-片层结构

The paper puts forward a cylindrical staggered-sheet structure micro linear stepping motor.

提出了一种圆筒型错片结构微型直线步进电机.

The basic types, structures and application of the guide structure punching die with spring pressure discharging plate and pillar die set used for punching thin sheet and ultrathin sheet metal blanking part are introduced.

介绍金属薄板、超薄板冲压件使用的导柱模架弹压卸料板导向结构冲模的基本类型、结构及应用范围。

Experimental study on the effects of material structure during thin sheet drawing process

材料组织性能对薄板拉深工艺影响的试验研究

By the relationship between temperature and recovery force, select temperature as the feedback and THE USES OF CORRUGATED SHEET Sheet Wave-Shaped Die Using AFS algebra and AFS structure, any human ordinary fuzzy concept can be represented.

根据温度与回复力的对应关系，选用温度作为反馈量，采用闭环控制方案对该结构进行形状控制，并将实验测得的主动变形波纹板结构的自由端位移与数值模拟结果进行比较和分析。

Oxide skin structure and thermodynamic analysis of hot-rolled coiled sheet

热轧卷取板的氧化层结构及热力学分析

Effect of annealing on fly line structure and properties of titanium steel explosive composite sheet

退火对钛-钢爆炸复合板中飞线组织的影响

Deducing the Location and Strength of Thermal Source Acting on Sheet-Metal Structure

受热薄壁结构热源定位及热强度识别方法研究

Lightweight Auto-body Structure with New Sheet Materials

用新板材的轻质汽车车身结构

Ultrasonic Non-destructive Characterization and Evaluation of the Elastic Modulus of Thin Metal Sheet and Spheroidized Structure in Low Carbon

金属薄片及低碳钢球化组织弹性模量的超声无损表征与评价

The thesis analyses the modal of silencer with three layers structure and two layers structure respectively, and the structures of which consist of sheet steel and glued rubber.

论文分别对三层结构与两层结构的钢片与橡胶层粘接结构的消音片进行了模态分析，得出消音片各阶模态频率随橡胶层厚度增大而减小。

Preparation and Structure Characterization of Corn Starch/ PCL Composite Sheet

玉米淀粉/ε-聚己内酯复合片材的制备及结构表征

A New Technology for Joining Sheet Metal Works Structure design of crimping type shield

一种新型板件连接卷边防尘盖的结构设计

The Application of Cellular Steel Sheet Pile Structure on the Port Engineering

格形钢板桩结构在港口工程中的应用

It should be modified to be strength weld and tight expansion structure. At the same time, manufacturing technology as modified for welding after expansion, tube sheet base should adopt the material of strength σ_s ≥ 320MPa.

建议改为强度焊加贴胀结构，并将复合管板基层改用屈服强度≥320MPa的材料，制造工艺改为先胀后焊。

A new jacquard bed sheet fabric was manufacted with bamboo fibre blended yarn, through the procedures of pattern and structure design, technological parameters selection and so on.

本文以竹纤维混纺纱为原料，配置相应的花纹图案、组织和工艺制成新颖的大提花床罩。

Welding technique of box composite profiled sheet for roof structure without purlin

无檩屋面结构箱形组合压型钢板的焊接技术