sic的例句大全

Then the incentive status and problems in the background, bases on motivation theory, put forward the corresponding improvement measures sic aspects of management, sales target evaluation, salary and welfare, occupation development, training and enterprise culture construction.

然后在激励现状和存在问题的背景下，根据相关激励理论，对销售目标管理、考核评估、薪酬福利、职业发展、学习培训及企业文化建设六个方面提出了相应的改进措施。

Damage evolution and microstructural characterization of a cross-woven c/ sic composite under tensile loading

2维C/SiC复合材料的拉伸损伤演变过程和微观结构特征

Temperature Field Optimization and Polytype Control in the Growth of 6 H-SiC Single Crystal

6H-SiC单晶生长温度场优化及多型控制

High temperature interfacial reaction between granular SiC and Ni in a composite plating

复合电镀层中SiC粒子与Ni之间的高温界面反应

Effect of High Temperature Treatment on the Ni-plating Hardened by SiC Grains

高温处理对SiC颗粒增强镍镀层的影响

Effect of low temperature treatment on residual stresses in sic_p/ 6061al composite

低温处理对SiC p／6061Al复合材料残余应力的影响

Tensile Creep Behavior of a 3D-C/ SiC Composite at Elevated Temperature

3D-C/SiC的高温拉伸蠕变性能

Tensile Creep Damage and Creep Mechanism of 3D-C/ SiC Composite

3D-C/SiC复合材料拉伸蠕变损伤和蠕变机理

Tensile Creep of UD-C_f/ SiC Composites Prepared by Precursor Pyrolysis and Hot Pressing at Elevated Temperature

先驱体转化-热压单向C f/SiC复合材料的高温拉伸蠕变

The empirical relation, the Monkman-Grant relationship and the Larson-Miller parameter can be used for creep rupture life prediction for the Three-Dimensional C/ SiC composite, The damage can be accumulated during the tensile creep tests at elevated temperature.

用应力经验公式，Monkman-Grant关系和Larson-Miller参数这三种方法来估算3D-C／SiC复合材料的蠕变持久寿命。

The present work will intend to further study tensile and creep behavior of notched 2D-C/ SiC composites.

本文研究了2D-C/SiC双边圆弧缺口试样的拉伸及拉伸蠕变性能。

That the low oxygen content continuous SiC fibers with 5%-6% oxygen content, can be prepared through two-step sintering program. Their tensile modulus with stable 2.2-2.7 GPa had been improved.

氧质量分数为5%~6%的低氧含量纤维也通过两步烧成工艺制得了性能稳定的连续碳化硅纤维，其强度为2.2~2.7GPa；

SiC particles and dimple are present in the fracture of the tensile specimen of SiC P/ MB 2 composites, there is interfacial debonding between the SiC particles and the matrix in the tensile fracture at the elevated temperature.

复合材料的拉伸试样断口存在SiC颗粒和韧窝，高温拉伸试样断口存在界面脱粘。

The manufacturability, microhardness, tensile-strength of SiC whisker/ Resin Matrix Composite was investigated.

考察了SiC晶须树脂基复合材料的工艺性，硬度，拉伸强度等性能。

According to the simulation results, combined with the actual process conditions, this paper developed a junction termination field limiting ring protected the high pressure Mo/ 4H-SiC Schottky barrier diodes based on experimental results indicate that such planar junction terminal protection structure is very effective.

根据实验结果，结合实际工艺条件，本文研制了具有结终端场限环保护的高压Mo/4H-SiC肖特基势垒二极管，根据实验结果指出此种平面结终端保护结构是很有效的。

The relationship of the strength of the SiCw/ Al composite and off-axis angle of the SiC whisker is studied with the analysis method of the simplified stress. Investigation on Off-axis Tensile Test for Determination of Shear Characterization of Composites

用简化应力的分析方法推导了SiCw Al复合材料的强度与SiC晶须偏轴角α的关系，并通过试验进行验证.偏轴拉伸测定复合材料剪切特性的研究

Rapid Wear Test of Steel Matrix PM Composite Reinforced With SiC Particles

SiC颗粒增强的钢基复合材料的快速磨损试验研究

At last, combining the technology of injection molding and combustion synthesis, h-BN+ SiC thermocouple-protection tube were fabricated.

结合注射成型技术和燃烧合成技术，成功制备了h-BN+SiC复合陶瓷陶瓷热电偶保护管。

Anisotropic Thermoelastic Stress Index of SiC

SiC各向异性的热弹性应力指数

Preparation of sic-b_4c composite film and its mechanical and thermoelectric properties

SiC-B4C复合膜的制备及其力学和热电性能