simulation process time的例句大全

The tearing mode instability and magnetic reconnection process in an anisotropic plasma ( P ⊥≠ P ∥, T ⊥≠ T ∥) are numerically studied by a two dimensional three component time dependant compressible MHD simulation.

应用二维三分量时变可压缩磁流体动力学模拟方法，数值研究了各向异性等离子体（P⊥≠P‖，T⊥≠T‖）中的撕裂模不稳定性和磁场重联过程。

The details of real-time data acquisition, control of tension process simulation and online performance analysis of the simulative testing bench are further illustrated.

在此基础上，文章进一步说明了系泊锚机张力仿真试验台的实时数据采集、仿真过程控制和在线性能分析等功能的实现细节。

At the same time, it can reduce the calculation time efficiently. The method proposed is an important improvement to the traditional numerical simulation, which can help to analyze the process of soil freezing, frost heave and thaw subsidence accurately.

该方法能够较为精确求解冻土温度场，是对传统方法的有效改进，也为土体冻结及冻胀融沉过程的精确分析创造了条件。

Key Technique of Real-Time Simulation in Diffusion Process of Hazardous Gases ── Probe into Solving Reversal Question in Gas Diffusion Equation

危险气体扩散实时仿真的关键技术&反求源强方法初探

At last, the three-tier C/ S architecture of terminal equipment supervision platform was designed. And completed the management of static data and dynamic data, achieved a simulation of real-time supervision and control of terminal equipment process.

最后设计了三层C/S体系结构的终端设备监控平台，实现了对静态数据和动态数据的管理，并模拟实现了终端设备的实时监控过程。

Through comparing the simulation results with relevant experiment data, it shows that actuator disc method can well simulate the process of load overshot and gradually recovering to the balance. The characteristic time of dynamic inflow is related to thrust coefficient and spanwise location.

与实验数据的对比显示，计算结果能够较好的模拟载荷过冲并逐渐恢复平衡的过程。

Moreover, the efficiency of code is improved and the working memory is reduced greatly, simulation results on FPGA show that the real time compression system can process 250 frames 512 × 512 gray images per second.

经FPGA仿真验证，该实时压缩系统每秒能处理250帧512×512的灰度图像。

Utilize a program to make the numerical simulation for the impact, has observed multi impact and multi sub-impact in a macrography impact, obtained the dynamics of beam and column and the time history of impact force in the total process.

利用编制的程序对碰撞过程进行了数值仿真，观察到了多次撞击以及一次宏观撞击中多次微碰撞的现象，得出了整个过程中梁、柱的动力学响应和碰撞力的时间历程。

Hybrid Real Time Simulation of Gas Turbine Acceleration Process

燃气轮机加速过程的数模混合实时仿真

The paper's important content and production are: ( 1) Set up three-dimensional elastic-plastic FE model for incremental sheet forming. Realize continuous simulation process for incremental sheet forming through imposing time-displacement curve to control its motion on the punch;

建立渐进成形工艺三维弹塑性有限元模型，通过对成形头运动施加时间-位移控制，实现了连续模拟过程；

Two independent processes-flight simulation process and demonstration process-are runed at the same time.

SatelliteStudio有两个独立进程，飞行模拟及演示进程和地面站模拟进程。

Simulation system may be used independently, and at the same time it can also be combined with transaction process system to construct powerful management information system to make decision support.

仿真技术可以独立使用，也可以同事务处理系统结合起来，构成功能强大的管理信息系统，以辅助决策。

The Time Series Analysis and Modeling Simulation of Dispensing Adhesive for Lay-down Process of Space Solar Cell Array

空间太阳电池帆板贴装涂胶过程时序分析与建模

This thesis introduces the application of time waveform replication technology in automobile component fatigue life prediction, and gives a brief presentation about its theory and two key technologies used in its process-System Identification and Object Simulation.

介绍了时域波形再现技术在汽车零部件疲劳寿命预测的应用，并对其原理和工作流程中的关键技术&系统识别和目标模拟进行了简要介绍。

Simulation results are employed to illustrate that the algorithm developed here can track and position maneuvering target in real time during orbit transfer process.

给出了扩展卡尔曼滤波实时估计增广状态向量的算法，仿真分析证明所述算法稳定、收敛，对机动目标具有较高的定位精度。

Three dimensional geometric model and real time display algorithm for simulation of cutting process and method of calculation of light density based on global illumination is proposed.

针对数控加工三维实时仿真系统的开发，研究了加工过程三维几何模型构建、仿真过程的实时动态显示以及基于全局光照明的加工环境光照计算的具体方法。

For creating large shared memory between real-time process and non real-time process may affect the performance and stability of the simulation system, this thesis presents a high-performance data exchange algorithm based on optimized data buffer queue.

论文针对实时进程与非实时进程间建立大的共享内存区影响系统性能和稳定性的问题，提出了基于缓冲队列的高效数据转存算法。

The real-time 3D simulation system visualizes the path planning process intuitively.

系统能够提供3D实时仿真，直观地显示路径规划过程。

And got the loading time by Romberg numerical integral method. Finally, programmed by VC++ 6 0 to calculate the pipeline system for the loading by gravity system through which can have quick process design calculation and operating simulation calcuation.

采用龙贝格数值积分法求解装车时间，应用VC++60高级语言编制了自流装车管路系统计算程序，应用该程序可快速进行工艺设计计算和模拟计算。

At the same time, using simulation results of Dynaform to analyse stress and strain distributing of metal in the forming process, and gains curves of forming load in the different cases.

同时利用Dynaform的模拟结果，分析了金属成形过程中的应力、变分布，得到了不同情况下的成形载荷曲线。