slide friction的例句大全

Slide friction and wear performances of single Ni coating, multilayer Ni coatingand multilayer composite coatings have been tested and studied.

对单层镍镀层、多层镍镀层和多层复合镀层的滑动摩擦磨损性能进行了测定和研究。

Near the latter point, the strain velocity of adhesive friction and that of slide friction is near to be equal and friction coefficient has almost no effect to the strain velocity with slide friction.

在轧件与轧辊分离处，变形速度为零，在这点附近粘着摩擦和滑动摩擦变形速度值接近相等，摩擦系数几乎不影响滑动摩擦情况下的变形速度。

The structure of Pd-Cu-Si alloy with Ni-P amorphous plating and its slide friction property were studied. It was indicated that the effect of load on the wear capacity was not obvious and the hardness of the wearing surface dose not increase during the wearing test.

用X－射线衍射研究Pd－Cu－Si合金玻璃丝和Ni－P非晶态镀膜摩擦付的结构，及其滑动磨损特性，表明负荷对磨损影响很大，磨损试验中，硬度没有增加。

The C/ CF/ Cu composites is higher than pure Cu not only in slide friction wear resistance but also in slide friction coefficient.

碳化和碳气相沉积处理的C/CF/Cu复合材料滑动摩擦磨损耐磨性高于纯铜，而且滑动摩擦因数也高于纯铜。

Slide friction characteristic of self lubricating material and its self lubricating mechanism

自润滑材料滑动摩擦特性与自润滑机理

Calculation of Rolling Strain Velocity in Consideration of Adhesive Friction and Slide Friction

考虑粘着摩擦和滑动摩擦的轧制变形速度的计算

The Calculation of Temperature-Increase in the Slide Friction Couple of a Plunger Pump

柱塞泵往复滑动摩擦副温升的计算谈谈如何制作幻灯片

Through the experimental research of friction coefficient of steel and bronze pair under boundary lubricated condition, a formula for calculating the pure slide friction coefficient is established.

通过边界润滑状态下钢与青铜摩擦副摩擦系数的研究与实验，得出计算纯滑动摩擦系数的公式。

Experimental Study of Friction and Wear of Three-Layer Composite Materials ( Mode ⅱ) Slide Track

Ⅱ型三层复合材料滑道的摩擦、磨损试验研究

Both the oil nylon and modified bakelite are monoblock materials, without stricter working environment requirement, and they are also useful materials for slide track, in spite of slightly higher values of friction coefficient.

油尼龙和改性胶木均系整体性材料，对工作环境要求不高，虽摩擦系数值稍高，但仍不失为一种有用的滑道材料。

Slide-resistant pile program has realized these fuctions which are given slip surface count internal friction angle, given the shape of sliding surface design calculation, given the landslide thrust design calculation of landslide, given sliding surface moment, shear force design calculation. 5.

抗滑桩程序设计，实现了对给定滑动面形状反算内摩擦角、给定滑动面形状进行设计计算、给定滑坡推力进行设计计算以及给定滑动面处弯矩、剪力进行设计计算的功能。

When sliding in the sliding-friction clutch of the automatic transmission, engine power is transferred through both hydraulic transmission and mechanic sliding transmission, which can improve transmission efficiency in a large range.

自动变速器中的滑摩离合器滑摩时发动机的动力同时通过液力传动和机械滑摩传动两条路线传递，它能够在大范围内提高传动效率。

Based on the study of implement mechanism of reciprocating electric micro saw, a kinematic and dynamic model is established. It reckons in friction of joints, actual mass of each rod and actual construction of slide and uses computer and means of numerical value calculating to imitate.

以微型往复式电动锯锯切机构为研究对象，建立了运动学和动力学模型，该模型计入了运动副摩擦、各杆的实际质量及滑块的具体结构，利用数值计算方法进行了计算机模拟。

Take Cu-base powder metallurgy strip and copper tin wire as friction, those experiment results were analyzed by introducing two relative stable coefficients, some rules between the above characteristics of slide and contact pressure, sliding speed and contact current were obtained.

以铜基粉末冶金滑板铜锡导线为摩擦副，通过引入两个相对稳定系数对实验结果进行分析，得出了滑板的载流摩擦磨损特性与接触压力、滑动速度和接触电流之间的变化规律。

Anti-slide monitoring of friction hoisting

摩擦提升防滑监测

FRICTION: Factor, which makes it difficult to slide one object over another, slows down motion and makes parts wear due to increase in temperature.

摩擦：使一物体在另一物体上滑动变得困难，降低运动速度，使温度升高而使零件磨损的因素。

It may be considered that the composite material is a kind of better slide track material, but, with certain working environment conditions required due to very thin friction reducing layer ( < 1 mm);

可以认为：复合材料是一种较好的滑道材料，只是减摩层很薄（小于1mm），对工作环境有一定要求；

aiming at the nonlinear friction factors that affect the performance of motion control at zero velocity, this paper analyses the characteristics of pre-sliding friction of x-y table of cnc machining center, and presents a simple and effective method of friction compensation based on these characteristics.

在分析数控系统中X-Y工作台静摩擦力特性的基础上，针对影响速度过零点运动性能的非线性摩擦因素，提出一种便于工程应用的摩擦力补偿方法。其中外界因素的影响最为重要。

C and ( cohesive force and interior friction angle of slide surfaces);

C和φ（滑动面的内聚力和内摩擦角）；

The angle of internal friction of slide plane has greater effects on anchor force, therefore, that should be selected correctly.

滑动面内摩擦角对锚固力影响较大，须正确选用。