spiral end的例句大全

The rims of the end part of the spiral shaft and a main spiral middle part are respectively provided with a straw cutter.

在螺旋轴尾部及主螺旋中部边沿分别有一断草刀。

The end face structure of a new type upstream pumping mechanical seal with double seal dams was developed because the solid particles were easily absorbed by the spiral groove type upstream pumping mechanical seal with the grooves on the internal wall to make the particles be damaged.

针对内径开槽的螺旋槽型上游泵送机械密封易于吸入固体颗粒而产生磨粒磨损的缺陷，研制开发出具有内外双密封坝的新型上游泵送机械密封端面结构。

A closed end was formed with one of the components in the center of the spiral, and away from the spiral center the stripes bent along the tangent of the spiral.

在螺旋中心某一组分形成闭合端，而其它区域条状相沿螺旋切线方向平行排列。

Dyes with the silver-plating law and Ji musa, may the very good demonstration mycelium assume spiral-shaped, its end or the beginnings and ends curved transfer the hook.

用镀银法和姬姆萨染色，可很好的显示菌体呈螺旋状，其一端或两端弯转成钩。

The line that extends along the end of the extra half-plane of atoms for an edge dislocation, and along the center of the spiral of a screw dislocation.

刃型位错中多余半原子面边缘的连线，或者螺型位错中错排螺旋的中心轴线。

the transformation design of end face spiral oil trough special lathe

普通车床改为端面螺旋油槽专用车床的设计

Che decides to assassinate Shun and things spiral towards a violent end.

一哲决定刺杀阿顺,一个暴力的结局渐渐临近.

The spiral of terrorism becomes never-ending.

恐怖主义活动没完没了，不断升级。

Moreover if, as often happens, the process descends into a vicious spiral of retaliation and counter-retaliation, the end result might be even worse.

而且，正如经常发生的那样，如果双边过程陷入一个报复与反报复的恶性循环之中，那么最终结果可能甚至更糟。

The results showed that the calculated depth of base, top width and spiral angle of flight at the start and end of the melting zone for extruder screw were in or close to the ranges recommended in literatures

结果表明，计算所得熔融段起、末端的螺槽深度、螺纹顶宽度和螺纹升角均位于或接近文献中所建议的最佳取值范围

A circular hoop sheet is punched with a spiral line, and one end of the spiral line penetrates through the connecting piece to contact a bottom plate to engage with the screw.

圆形箍片冲制有螺线一端穿过连接件贴靠在底平面并与螺钉相啮合。

CNC grinding model and technology of an equal spiral angle cone ball end miller

圆锥球头立铣刀的CNC磨削模型及工艺

The hot zone is formed by cutting a double spiral slot which reduces the cross sectional area through which current flows, resulting in higher resistance than the cold end.

发热部是双螺旋切槽，在电流通过时可以减少其横截面积，因而发热部的阻值比冷端部的阻值大。

Far out in the uncharted backwaters of the unfashionable end of the western spiral arm of the Galaxy lies a small unregarded yellow sun.

在古老银河系的螺旋状西臂末端，任何地图都还没标示过的蛮荒地带，有个丝毫不引人注目的小小黄色恒星。