static structural analysis的例句大全

Lastly, a static structural analysis is taken for a vehicle door inner panel part drawing with the method.

最后，应用该方法对某车型车门内板零件的拉延模具进行静力结构分析，得到了其模具型面变形的主要趋势。

Performance Analysis and Structural Improvement of the Static Components Within the Single-stage Centrifugal Compressor

单级离心压缩机静止元件的性能分析与结构优化

Based on the model experiment and finite element analysis, structural static performance of a pressure spherical model with a big viewport is discussed in this paper.

结合模型试验和数值计算对大潜深、带大开口的球形耐压结构静态力学性能进行了研究。

structural analysis and test research on static pressure air supply duct

静压式送风风道的结构分析及试验研究

It needs to round off the optimized structural dimensions and have another finite element analysis for the fuse impact plate, under meeting its static and dynamic characteristics, to get the ideal structural dimensions.

对优化后的几何尺寸进行圆整，对优化后冲击盘模型进行有限元分析，在满足其静态，动态特性的前提下，得到最终理想的冲击盘模型尺寸。

First of all, the kinematics analysis is carried out through establishing D-H model from the structural characteristics of it; On this basis, a static error model is established, so we can analyze static error caused by error of mechanism.

首先从其结构特点出发，建立D-H模型进行运动学分析；在此基础上建立静态误差模型，分析由机构误差所引起的静态误差。

Influence of structural height on the results of static pushover analysis of structures

结构高度对静力弹塑性分析结果的影响

Displacement Shape Vector Selected for Static Pushover Analysis of the Structural Seismic Respones

结构地震反应Pushover位移形状向量的选取

The static analysis and structural optimization of the key seal parts and components of vacuum clamp are researched in this thesis using finite element analysis software ANSYS.

本文利用通用化有限元分析软件ANSYS作为分析工具，对真空吸夹具的密封关键部位及密封元件进行了有限元静态分析和优化设计。

in this paper, the alternate iteration method is used in static analysis of cable truss hybrid structural system, and the simplified non damping free vibration equations have been drawn.

本文采用交替迭代法分析索&桁结构体系，并导出了这种杂交结构无阻尼自由振动的简化方程。

Structural Static Analysis of Steel Tube Concrete Arched Combined Beam Aqueduct

钢管混凝土拱组合梁渡槽结构静力分析

The model of the aluminum alloy wheel classified as 16 x 6.57 is built. Static stress analysis is carried out to study the influence of bolt pre-tension, centrifugal force and the cornering force to the structural as well as the distributing rule of stress and strain.

首先根据试验工况建立起16×6.5J车轮的有限元模型，通过静力分析研究螺栓预紧力、旋转离心力和试验弯矩对车轮结构强度的影响以及车轮结构的应力应变分布规律。

Based on the theory of finite element analysis, combining engineering practice, using the bridge structural analysis software, establish the finite element model of the extradosed cable-stayed bridge, compared the static load test check the model.

在斜拉桥结构分析理论基础上，以实桥为工程背景，运用桥梁结构分析软件，建立矮塔斜拉桥空间有限元模型，以静力荷载试验为对比校核模型。

the probability density evolution method for the analysis of linear stochastic structural static response is proposed.

提出了线性随机结构静力反应的概率密度演化方法.