strain force的例句大全

during rupturing process, force results calculated by dm are higher and lower by ndm than experimental ones due to higher strain rate sensitivity.

由于有限元方法只能描述连续介质，因此对于断裂破坏阶段，NDM模拟载荷大于试验结果，DM的载荷小于试验结果，这是由高应变速率敏感性造成。

the interrelation of expansive force with water absorption rate and the law of expansive force with expansive strain are studied.

并进一步探讨了膨胀红砂岩膨胀力与吸水率的相关性，继而研究膨胀红砂岩膨胀力与膨胀变形的规律。

the screen should be brighter than the ambient light-overly bright overhead light and streaming daylight force the eyes to strain to see what is on the screen.

显示器应该比环境光亮一些——过亮的顶灯或者强烈的阳光，会迫使眼睛非常用力地望向屏幕。

through analysis the reasons influencing measuring stability have been found out, which are the flexure strain and structure resonance produced by the transmission axle under the function of the gearing-in force of the reduction gear.

虽然与传统的测量方法一致，但经过理论分析，得出了这种测量方式机械结构影响测量稳定性的原因，即传动轴受减速器齿轮啮合力作用产生的弯曲应变和结构谐振对测量精度影响最大。

numerical study on influence of rupture strain on crack driving force of welded joints with damage

断裂应变对含损伤焊接接头裂纹扩展驱动力影响的数值

The deformation process of heavy rail at 800-I pass has been simulated using nonlinear finite-element software MARC/ AutoForge by three dimensional thermo-mechanical coupled elastoplastic finite element method ( FEM), and the equivalent stress and strain field, temperature field and rolling force of rolling billet were analyzed.

采用非线性有限元软件Marc Autoforge，通过三维弹塑性热力耦合的有限元方法模拟了重轨800I孔的变形过程，分析了轧件上等效应力、应变场、温度场和轧制力。

Knowledge and experience is preferred acquisition for physical test including strain, torque, force, pressure, temperature etc.

希望具备物理量测量的知识和经验,如应变 、 扭矩 、 力 、 压力 、 温度等.

A model of accumulating stress and strain along a fault under steady-state boundary force and the discussion on the seismic risk area

定常边界力作用下断层应力应变积累的模拟与地震危险区讨论

Contrast metrical data of strain gauges and grating sensors, it is indicated that fiber bragg grating sensor can be a reliable method to measure turning force.

对比电阻应变片和光栅传感器测量数据，分析两种传感器测量的优缺点，验证了光纤光栅在铣削力测量方面的可测性和准确性。

The optimization preform shape checked by forward operation and the results show that the variation of effective strain trend to uniform, the forming force and the effective stress are decreased. 4 、 The study of multilayer metal die.

通过对优化结果进行检验，可以看出优化后的模型变形更加均匀，使得终锻模的等效应力和成形所需的动力均有所减小。4、多层金属热锻模的研究。

The model of the aluminum alloy wheel classified as 16 x 6.57 is built. Static stress analysis is carried out to study the influence of bolt pre-tension, centrifugal force and the cornering force to the structural as well as the distributing rule of stress and strain.

首先根据试验工况建立起16×6.5J车轮的有限元模型，通过静力分析研究螺栓预紧力、旋转离心力和试验弯矩对车轮结构强度的影响以及车轮结构的应力应变分布规律。

Free energy function including elastic strain energy and chemistry energy is derived, then phase transformation driving force is obtained.

推导出由弹性应变能和化学能组成的应变能函数，进一步得到相变驱动力的表达式。

Deforming Force Relationship Between Axisymmetric State and Plane Strain State in Extrusion Technology

挤压工艺轴对称状态与平面应变状态变形力之间的关系