strain test的例句大全

Research into low strain dynamic test of foundation pit

低应变动力检测基桩的应用研究

Analysis and Application of Low Strain Dynamic Test Technology in Construction of Pile Foundation

低应变动测技术在建筑桩基工程的分析与应用

Metallic sheets& Tensile strain hardening exponents ( n-values) test method

GB/T5028-1985金属薄板拉伸应变硬化指数（斜值）试验方法

Research on Materials Test Technology of Real Stress-Strain Based on Machine Vision

基于机器视觉的材料真应力&应变测试技术研究

Did the pulling test in one dimension then obtained the tensile destructive load, stretch ratio, Lagrange stress, Cauchy strain of the above three kinds of cartilage.

以一维拉伸的方法得出了肩髋膝关节软骨的破坏载荷、伸长比、Lagrange应力、Cauchy应变等。

Calculation Model and Experimental Verification on True Strain and True Stress in Hot Tensile Test

高温拉伸试验中真应力真应变的计算及试验研究

When the sensor is used to test steel bar after it has been calibrated, the accuracy of the sensor is better than ± 2.5% for the tension strain and ± 2.9% for the compression strain.

定标后传感器测量钢筋拉应变时，其应变的精度优于±2.5%；测量混凝土压应变时，其精度优于±2.9%。

Base on the test of reinforced membrane elements and regression analyses, the formulas of tension strain produced compressive stress are presented respectively before crazing of concrete, before yield of steel bars, and tensile strain less than 0.008 and greater than 0.008 in this paper.

文章基于钢筋混凝土薄膜元受拉试验和回归分析，给出混凝土开裂前、钢筋屈服前、拉应变小于0.008和大于0.008时的应力应变关系式。

The check of the belt strength and strain is bosed upon that tension and strain. Test method for electric strength of insulating adhesive tape at power frequency

胶带强度和应变的校核均应以该处胶带断面的张力和应变为依据。GB/T7752-1987绝缘胶粘带工频击穿强度试验方法

Slow strain rate tension test of high-strength aluminum alloy 7075

LC4高强铝合金的慢应变速率拉伸试验

The patch test function for C~ 1 axisymmetric couple stress is quadratic function. And it proves that the quadratic patch test function does not contain constant shear strain term either.

轴对称C~1偶应力有限元检验函数为二次函数，本文证明二次检验函数也不含常剪应变项。

It was pointed out that in tensile test with specimen of C-grade casting steel, the load-halt method or the judgment from the pointer swing of strain instrument could not give clearly the yield point except the graphical analysis method.

指出测定C级钢拉伸试样屈服点时，用载荷停顿法或指针法，屈服现象不明显，只有图解法可一次测出未知屈服指标。

Take full account of the preparation of standard test sample, set of device parameters, temperature and other details on the polyethylene pipe specimen, constant strain rate tensile, creep test and relaxation test are accomplish.

充分考虑标准试验试样制备、设备参数设置、温度调节等细节，对聚乙烯管试样进行等速率拉伸、蠕变、松弛试验，通过合理的试验处理得到真实应力应变曲线以及力学性能参数。

At the same time, through the microscope test of surface, the effect on craze density by strain rate has been investigated as well.

同时通过表面银纹显微镜观察实验，研究了应变率对银纹密度的影响。

The methods of creep test to get both curves of tensile creep rupture load vs time and creep strain vs time are compared. The procedures to extrapolate the two types of creep curves are presented.

比较了获得拉伸蠕变破坏荷载-时间曲线以及蠕变应变-时间曲线的试验方法，给出了外推这两种蠕变曲线数据的处理步骤。

By means of sticking the electric-resistance strain pieces on the transverse of the planetary gear, we have done the dynamic test of contact tooth pair numbers of the involute planetary transmission with mi-nor tooth difference in which the internal gear is used as the output member.

我们采用在行星轮端面贴电阻应变片的办法对内齿轮为输出构件的渐开线少齿差行星传动进行了接触齿对数的动态实测。

In order to verify the analysis results, static test on two spatial full-sized solid models is carried out, and the step-by-step load apply system is adopted to find out the stress and strain value of each testing point.

为验证计算分析结果，对两个受力较大的铸钢节点进行了足尺实体静力试验，采用分级加卸载制度获取各级荷载下各观测点应力应变值。

The Preparation of Monoclonal Antibodies Against CSFV-C Strain and Development of Rapid Test Strip for CSFV

猪瘟C株单克隆抗体制备和猪瘟胶体金快速诊断试纸条的研制

The effect of aging and cold working rate on the trans formation properties and the recovery strain in Ti-50. 5mol% Ni shape memory alloy have been investigated with DSC ( Differential Scanning Calorimetry) and mechanical test under a constant stress.

用示差扫描热分析仪（DSC）和恒应力拉伸试验研究了时效和冷加工率对Ti-50.5mol%Ni形状记忆合金相变特性和回复应变的影响。

This paper is based on result of visioplasticity test of thick cylinder during axial pressure with support of mandrel, velocity field and strain rate field were established.

本文根据厚壁圆管在两端夹持、有芯轴支撑、轴向加载的条件下，视塑性试验流线分布的结果，建立了变形区域的速度场和应变速率场。