surface bonding的例句大全

Testing Surface Bonding Strength for Thin MDF

薄型中密度纤维板表面结合强度的测试

The analysis results showed that: after 50 cycles under temperature drop of 980 ℃, no cracks seen by naked eyes occurred on the surface and no debonding phenomenon happened in the interface bonding zone.

分析结果表明：在温差980℃下循环50次后，其表面未出现任何肉眼可见的微裂纹，且其界面未出现脱粘的现象。

In the present study, we investigated the effects of surface characteristics on the bondability of an Au-Au thermosonic bonding system.

在最近的研究中，我们调查了表面特性对金-金超声压焊系统的影响。

Bonding mechanism of crosshead ductile iron surface and tin pewter layer

十字头球铁表面与锡锑轴承合金层结合机理

Using acetylene torch to make tin pewter welding rod melting and bonding with the tin surface to improve the bonding force.

采用氧乙炔火焰将锡锑轴承合金焊条熔化结合在锡表面，以提高两者的结合力。

In thermal bonding process, surface affinity treatment, vacuum pro-bonding and bonding temperature control were studied experimentally without clean room condition.

在高温键合工艺试验中针对表面亲和处理、抽真空预键合以及键合温度时序控制等方面进行研究，重点讨论了非超净环境下高效预键合方法。

Effect of thermal spray process on bonding strength of aluminum coating on glass surface

热喷涂工艺对玻璃表面铝涂层结合强度的影响

At the same time, accumulated thermal deformations thus surface sink and rupture due to higher bonding temperature can be reduced.

同时，又可以抑制过高焊接温度所带来的升温热变形积累，从而减小表面塌陷变形或断裂。

Results show that cold plasma treatment improves the surface polarity and impregnation of carbon fiber, which increases the bonding property of carbon fiber braid/ epoxy composites, and therefore improves interfacial properties of composites.

实验结果表明，冷等离子体处理提高了碳纤维表面活性、浸润性，从而改善了碳纤维缝编织物/环氧复合材料的界面粘结性能，进而改善了复合材料的界面性能。

Effects of different porcelain bonding systems combined with ceramic surface treatments on the shear bond strength between porcelain and bovine enamel

不同瓷粘结系统及表面处理方式对瓷与釉质间粘结强度的影响

Cephalexin was primarily adsorbed in cationic and zwitterionic forms. Electrostatic attraction, hydrophobic interaction and chemical bonding with surface functional groups were demonstrated as primary mechanisms for cephalexin removal.

头孢氨苄主要以阳离子和两性离子的形式被活性炭吸附，其吸附机理包括静电吸引、憎水亲和及与表面官能团共价结合。

The morphological structure analysis indicated that PE-g-MAH addition decreased the surface tension, making the two phases disperse uniformly, enhancing the bonding strength of interface and improving the compatible property of nylon 11 and PE.

形态结构分析表明，接枝物的加入，降低了界面间的表面张力，使两相分散均匀，分散度提高，增强了相间的粘接力，改善了尼龙11与聚乙烯的相容性。

The Auger elec-tron spectroscope ( AES) analysis of the fracture surface after the surfa-ce being sputter etched show that the bonding between SiC whisker and aluminium matrix is quite good.

用俄歇电子谱仪（AES）对断口表面和对它进行溅射剥层后分析的结果表明SiC晶须与基体Al结合良好。

The results show that the WC particles partially dissolve in the liquid of steel, and the C and W contents substantially increase in the matrix close to the bonding surface, indicating that the alloy element diffusion and transformation occur.

结果表明：WC颗粒溶解于高温钢液，微区内W、C元素的含量显著提高，存在合金元素的相互扩散和迁移；

For grinding samples, the bonding strength increased with increase of surface roughness;

砂纸打磨条件下，随表面粗化程度的增加，结合强度增加；

Effect on bonding strength of sanding surface roughness of wood and bamboo

磨削木竹材表面粗糙度对胶合强度的影响

Conclusions: Sandblasting is a suitable surface treatment for the bonding of the zirconia ceramics.

结论：喷砂处理的氧化锆陶瓷的黏结强度最高，喷砂是适合牙科氧化锆陶瓷黏结的表面处理方法。

effect of surface roughness on the void closure time in diffusion bonding

表面粗糙度对扩散连接孔隙闭合时间的影响

Comparing with the diluted sample, the DRIFT spectra of unmixed sample appear an intensive peak at about 1 190 cm-1, which indicates the Si-O bonding on the particle surface.

研究发现，与KBr稀释的样品相比，氮化硅粉末纯样品的漫反射红外光谱在1190cm-1波数处出现了对应于颗粒表面Si&O振动的尖锐强峰。

Methods Compared the bracket bonding failure rate and ARI counts of 30 cases which treat the etched enamel surface with 5s air water gun rinsing, wet cotton ball wiping and alcohol cotton ball wiping respectively.

方法对30例气水枪冲洗，湿棉球擦拭及酒精棉球擦拭等三种不同酸蚀后牙面处理方法的临床托槽脱落率及粘接剂残留指数ARI进行回顾性统计比较。