surface crack的例句大全

Under offset load, the stresses around the crack tip and the surface deflection in the pavement with cracks have a great increase compared with that without cracks.

在偏荷载作用下，含表面裂缝的路面结构裂缝尖端的应力以及路表弯沉较无裂缝结构有很大的增长。

In view of the armor plate crack phenomenon of amph~ ious armored vehicles, this article designs a test experiment on the surface stress.

针对两栖装甲车辆装甲板裂纹现象，设计了表面应力测试试验。

The laser-controlled thermal stress cutting induces and controls the crack propagation by using the thermal stress which is caused by the surface temperature field gradient in the laser cutting. And it is an effective manner to split the glass, ceramics and other brittle materials.

激光热应力切割技术通过激光束切割材料表面时引起的温度场梯度变化产生热应力，诱导并控制裂纹扩展，从而分割材料，是对玻璃、陶瓷等脆性材料切割的有效方法。

C/ C composites matrix for embedding method for SiC coating effect is significant, SiC coating with carbon matrix coefficient of thermal expansion difference, causes micro crack generation in coating surface.

C/C复合材料基体对包埋法制备SiC涂层的影响较为显著，SiC涂层由于与炭素基体热膨胀系数差异，引起涂层表面微裂纹的产生。

Plenty of oxidation etching pits are found on the surface of the specimen after the thermal fatigue test, and the surface principal crack is prone to propagate through these etching pits.

实验结果发现，试样表面出现大量的氧化腐蚀坑，表面主裂纹优先通过这些腐蚀坑扩展。

By using the numerical Laplace inversion method, the variations of the temperature distribution along the crack surface and extended line and transient thermal stress intensity factors are presented.

利用Laplace数值反演方法，给出了裂纹面及延长线上的温度分布及动态热应力强度因子随时间变化的规律。

The main cause of thermal shock fatigue is the co-action of micro-cracks, crack bridge and deflection," crushed particles" and roughness on the crack surface during thermal shock cycling.

热震过程中的微裂纹，裂纹桥接和偏转，热震裂纹表面的碎粒及粗糙性等的共同作用是Al2O3-TiC复合陶瓷热震疲劳产生的主要机制。

At present, along with new wall material, outer wall coating and new stratification plane waterproofing material vigorously promoted used, a higher request is set to anti-crack, anti-seep and the performance of surface approved greasily of the mortar overall plastering surface layer.

目前，随着新型墙体材料、外墙涂料和新型层面防水材料的大力推广使用，对砂浆整体抹灰面层的抗裂、抗渗性能和表面批腻刮荡等提出了更高的要求。

This paper studies the influence of the change of flow direction of cooling water at the botton of ingot mold and the mold material on the crack and the inner surface roughness of the ingot mold.

对锌锭模制造经过多次的改进试验，主要改进了锌锭模下端面的冷却水流向和材质，研究其对锌锭模的断裂、内腔表面粗糙度的影响；

Analysis of Causes for Crack on Surface of Large Bearing

大型轴承表面裂纹原因分析

Cause of Crack on Surface of Plate during Bend Test

钢板弯曲试验后出现裂纹的原因

Causes and measures of longitudinal crack on slab surface

板坯表面纵裂纹的成因与控制

The surface of nickel/ plate should be smooth and neat without interlayer, crack, peeling, bubble and foreign substance.

带材/片材表面应光滑、清洁。不应有分层、裂纹、起皮、气泡和夹杂。

Eggshell crack detection based on the surface wave analysis.

采用表面振动波分析技术检测鸡蛋蛋壳裂纹。

The result has shown that the fracture was caused by such surface defects as fold crack in section A at connecting rod small end.

结果表明，断裂由连杆小头A截面的表面缺陷（折叠裂纹等）引起。

Influence of lubricant on stress intensity factors of surface lean crack in rolling/ sliding contact

润滑油对接触表面斜裂纹尖端K因子的影响

ultrasonic flaw detector, detecting if there is crack on the surface of the tube inside and outside

超声波探伤设备，探测钢管内外表面的缺陷

Striation mark on lateral crack surface

论水平裂纹表面的扩展条纹

Improper rework practices can result in unscheduled maintenance or surface damage that causes crack initiation.

翻修不当可能会造成非计划性维修和表面损伤从而造成裂纹。

Simple talking about reasons and treatment of crack of water stabilized gravel base road surface

水稳砂砾基层路面裂缝成因分析及处理