surface deformation的例句大全

Because of its spiral surface which causes asymmetry, the deformation state of spring seat in the stamping process is much more complicated than that of general symmetry part.

弹簧座由于其螺旋面带来的非对称性，使其冲压成形过程中的受力变形状态要比一般的对称件复杂得多。

The problem of surface tidal deformation of the earth is expanded to that in the interior of the earth.

把地球表面潮汐形变问题扩展到地球内部。

There are many plastic deformation and enfolded districts on the weared surface, which leads to the fact that the slice come off from pure aluminium surface and the wearing rate is high.

结果表明纯铝表面发生粘着磨损，存在大量塑性变形和折叠，导致片状脱落，磨损率高；

The simple bounding surface elastoplastic-viscoplastic model was used in Biot' consolidation theory. The deformation and pore pressure of road soft clay improved by heaped load precompression was calculated numerically.

在Biot固结理论中使用简化的边界面弹塑/粘塑性模型，对超载预压法处理公路软基全过程的变形和孔压进行数值计算。

For many years aeroneer is always expected that they can manipulate aircraft not by the control surface, but directly by the deformation of airplane wings to change aerodynamics, so as to obtain the best aero performance.

多年来飞机设计师一直期望不用舵面，直接依靠机翼变形来改变空气动力进行飞行操纵，以获得最佳的气动性能。

The plastic body is usually looked upon as a slip fault surface in the theoretical analysis of the thrust structure, thus the compound action of plastic deformation and thrust deformation are ignored in the same region.

在冲断构造分析过程中，常常把塑性岩体仅仅作为滑脱层看待，忽略了一些地区塑性变形与冲断构造变形的复合作用。

The test of rolling the differential thick lead sheet shows the internal surface hollow and hole defect is resulted from uneven deformation of rolled piece. The basic way to avoid the two defects is put forward.

通过轧制差厚铅板实验说明规律性的热连轧无缝钢管内表面凹坑、孔洞缺陷的形成主要是由于轧件不均匀变形所致，并提出避免这两种缺陷出现的基本思路。

an analysis of great deformation of surface displacement field in mining

矿山开采地表位移场的大变形分析

The results show that the surface microphotograph yielded in multiple step machining with slow feeding and in one step compound process is satisfactory, and there are fewer defects, lower deformation and thinner metamorphic layers;

结果表明，钻扩铰多步慢进给工艺和一步复合制孔工艺所加工出的表面，平整、光滑、加工缺陷少、晶格变形小、变质层薄；

Result indicates that surface decarburization in thread root of bolt and microcrack in plastic deformation layer of thread surface are the main causes to reduce seriously the strength of bolt and result the bolt rupture failture.

结果表明，螺栓的螺纹根部表面脱碳，螺纹表面塑性变形层中存在微裂纹，表面脱碳和微裂纹严重降低了螺栓的强度，导致螺栓断裂失效。

Observation on Surface Building Deformation Caused by Underground Mining

采矿引起地面建筑物变形的摄影观测

Utilizing the theory of differential geometry, elastic deformation and wear abrasion and running-up of the tooth surfaces in circular arc gears, an elastohydrodynamic lubrication ( EHL) model of point contact with two-dimensional surface velocities was developed.

从圆弧齿轮齿面微分几何分析、弹性接触变形和跑合磨损分析，建立了具有二维表面速度的点接触弹流基本模型。

Simulation Study on the Movement and Deformation Laws of Ground and Bedrock Surface under the Condition of Sub-level Caving Mining

放顶煤开采地表及基岩面移动规律模拟研究

The other important reason for size effect of fracture energy is non-linear distribution of deformation nearby fracture surface and fracture energy distribution on fracture surface is not even also.

断裂能尺寸效应的另一主要原因在于断裂面附近的变形是非线性分布并且断裂能在断裂面内的分布也不均匀。

A Biomechanical Model for Simulating the Deformation of a Leukocyte Adhered to the Surface of a Blood Vessel under Steady Shear Flow

黏附于血管壁表面的白细胞在稳定剪切流动下发生变形的生物力学模型

Influences of sharpness of diamond tool cutting edge on the cutting deformation and quality of cutting surface

金刚石刀具刀刃锋锐度对切削变形和加工表面质量的影响

Influence of the Strength of Bearing Surface on Stress and Deformation of Arch Dams

建基面强度对拱坝应力、变形的影响

By analyzing the obtained variation of the surface area and the key factors affecting droplet deformation, the formula of droplet surface area is obtained by regression analysis, and fuel droplet evaporation rate model was successfully corrected.

本文通过分析得出了影响液滴变形的关键因素和液滴表面积的变化规律，应用回归分析方法得出了液滴的表面积变化公式，并对燃油液滴蒸发速率模型进行了修正。

Research on the Effect of Deformation of Bearing Surface on Lubrication Performance of Misaligned Journal Bearing

轴承表面弹性变形对倾斜轴颈轴承润滑性能的影响

The grinding affected layers on bearing surface consist of absorption layer, oxide layer, white layer, overtempering and plastic deformation layer.

变质层由表至里是由吸附层、氧化层、白层及过回火塑性变形层组成。氧化层是Fe与合金元素氧化物组成的混合结构，并存在Si的表面富集。