tangential stress的例句大全

The method of overcoming the defects is to reduce the axial pressure of the rotating wheel and to reduce tangential stress.

克服缺陷的方法是减少旋轮的轴向压力，降低切向应力。

Through numerical treatment and normal-tangent iteration, the normal contact stress, tangential stress and contact width of plastic gears are acquired.

对该积分方程组经过数值处理和法向&切向问题的选代运算后，则可以求得塑料齿轮副啮合轮齿的法向接触应力、切向接触应力和接触区宽度。

Analyzed from the stress angle, the lathe-bed is mainly imposed by a vertically upward force, moreover, the lathe-bed is not slender, so the direction of tangential stress should not be ignored.

从床身的受力角度看来，床身主要受到垂直方向上的力，而且床身不是细长的结构，切应力的方向不能忽略。

The tangential stress at the boundary can not be gained directly in the application of Boundary Element Method to analysing elastic stress.

在用边界元法作弹性应力分析中，不能直接计算出弹性体边界切向应力。

When composite flywheel rotates in high speed, there will be greater radial stress and tangential stress because of internal force.

复合材料飞轮转子在高速旋转时，由于惯性力的作用，会产生较大的径向应力和环向应力。

Relatively, the different radial gradient of the elastic constants will have a great influence on the tangential stress and the radial displacement.

相对而言，弹性模量沿径向的不同梯度模型对环向正应力和径向位移的影响要大一些。

The results showed that no TTS was observed under radial fretting condition. The tangential stress and displacement of the contact surface were the factors controlling the initiation of TTS, which supported that the formation of TTS was characterized by plastic deformation.

结果表明，TTS形成的主要控制因素是表面切应力和切向位移，TTS形成过程呈现塑性变形特征；

The results show that opening point, opening angle, maximal tangential stress and critical load vary with aspect ratio and inclined angle. The most dangerous inclined angle is obtained accordingly.

结果表明，开裂点、开裂角、最大切向拉应力和临界载荷随椭圆的纵横轴比和倾角的不同而变化，由此可得到最危险的倾角。

The tangential stress was still the major factor for controlling the growth of white layer under grease lubrication.

润滑条件下表面切应力τ仍是微动白层形成和发展的主要控制因素。

The radial and tangential stress maximums are both in the inner surface of bearing alloy.

径向应力与周向应力的最大值位于轴瓦合金层内表面。

The normal and tangential stress components along the slip direction on the earthquake fault plane are then found by co-ordinate transformation.

通过坐标变换，得到了发震断层面中的正应力及沿错动矢量方向的剪应力。

In the vicinity of the borehole, the tangential stress is maximum and the radial stress in minimum.

得出在钻孔附近切向应力最大，径向应力最小。

In this paper, the effect of decoupling charge in smooth blasting on maximun tangential stress, relative strain amplitude, the peak value of kine-tic strain and the expansion of crack formed by blasting has been expounded.

文中叙述了不偶合装药在光面爆破中的作用，如对最大切向应力、相对应变幅值、动应变峰值和爆破裂隙扩展等的影响。

The measured results shows that the damage of the bit body was mainly caused by tangential stress.

测定结果表明，钎头体主要是由切向应力引起账裤破坏。

The method developed in the article also can be used to calculate the boundary tangential stress of higher boundary elements.

所研究的方法也适用于高次边界单元的边界切向应力的计算。

Determination of fracture core region and modified maximum tangential stress criterion

金属材料断裂核区的确定与对最大切向应力断裂准则的修正

Concept of Thermal Contact Resistance and Influences of Hysteresis and Tangential Stress

接触热阻的概念、滞后效应以及切应力的影响

The maximum tangential stress may appear inside the disk or cylinder instead of at the boundary.

最大环向正应力可能出现在圆环/筒的内部，而不是在边界上。

The distribution of normal stress and the tangential stress of rim-tyre-road contact position are studied.

研究了基于Yeoh模型的轮胎与轮辋和地面接触部位法向力和切向力的分布。

In this paper, difference method is used for solving tangential stress at the boundary on the basis of BEM.

本文在边界元法分析的基础上，用差分法计算边界切向应力。