taper ratio的例句大全

The influence of sweep angle and taper ratio on the characteristics of wingtip stalling is discussed.

讨论了后掠角和尖削比这两个机翼外形参数对翼尖失速特性的影响。

The task of the initial sizing is to find the primary parameters of aircraft, including the takeoff wing loading, thrust-to-weight ratio, takeoff weight, wing area, aspect ratio of wing, wing sweep, thickness and taper ratio to match the mission requirements.

其任务是找到能满足飞机性能要求的飞机主要参数。这些参数包括：起飞翼载、推重比、起飞重量、机翼面积、机翼翼载、机翼后掠角、机翼相对厚度和机翼梯形比等。

The maximum stress in slab surface increases with decreasing the taper ratio of crystallizer, and with increasing the slab width.

随着结晶器锥度减小和连铸坯宽度的增加，连铸坯表层最大应力增加；

Taper ratio and optimum value of taper-flat sector thrust bearing with double-side resistive oil edges posterior inclined plane appliance

双封油边斜&平面固定瓦推力轴承的最佳斜面比

The most principal factors that influence the supersonic atomization process include the flow ratio of the gas-liquid metal ( GMR) value, the flow of atomizing of gas and the range of the inverse vortex taper.

影响超音速雾化工艺最根本的因素有气液质量流率比（GMR）的大小、雾化气体流量和倒涡流锥范围，三个因素的值越大，对形成细粉越有利；

In order to evaluate these two equations, they ase compared respectively with other taper equations and volume ratio equations in use, using data of Chinese fir ( Cunninghamia lanceolata Hook) stands. Results show better effectiveness of these two equations than others.

为了评价这两个方程，利用杉木材料分别与其它已有削度方程和材积比方程作了比较，结果表明这两个方程的效果较好。

The hole of which the diameter is 2 mm, the depth/ diameter ratio is more than 20 and the taper is less than 0.5% can be machined successfully on the general sink EDM machine tool by using the tube column electrode or the tube flatted electrode.

分别用管状圆柱电极和削边电极在通用电火花成形加工机床上成功地加工出直径为2mm、深径比大于20、锥度小于0.5%的深小孔。

Forth, we present a design technique for directional gain enhancement in low profile tapered slot antennas; we study along a yagi-like dual tapered slot antenna ( DTSA) which features high gain, high front-to-back ratio and broadband characteristics with a short taper profile.

第四，我们提出了渐变槽天线定向增益增强的设计方法。我们同时研究了具有高增益，高前后比和宽带的Yagi形双锥形槽（DTSA）天线。

Utilizing rectangular approximate in 3 dB fused-tapered optical fiber coupler coupling ratio is analyzed theoretically.

利用矩形近似理论对用熔锥法制作的耦合器分光比进行了分析.

The molding size was designed according to the average shrinkage ratio of polystyrene, demoulding mechanism of taper microgroove and arc side core-pulling mechanism was used in the mold.

按聚苯乙烯的平均收缩率设计计算模具成形尺寸，在模具中设计了圆锥细纹脱模机构、弧形侧抽芯机构。

Evaluations are also made on taper equations and volume ratio equations being compared.

另外对所比较的削度方程和材积比方程作了评价。

The results showed the voidage ratio of taper spiral packing,θ-ring packing and metal gauze corrugated packing was 0.823:0.947:0.855, and under the same liquid sprayed density, the pressure drop ratio of unit height of packing layer was 0.58:1.10: 0.62.

流体力学性能测试中，锥度螺旋填料、θ环和丝网波纹填料三种填料的空隙率之比为：0.823：0.947：0.855时，在相同喷淋密度下，单位高度填料层压降之比却为：0.58：1.10：0.62。

Previous formulae [ 1,2] took the web ratio factor into the coefficient of length, regarding web-tapered member as a uniform one with the same cross-section of the small end.

以往的公式[1,2]采用将楔杆等效为以小端截面作为等直杆的截面、将渐变的影响计入计算长度系数的方法；

Due to the strong constraint from the base and the indenter, the size effect of micro-pillar strongly depends on the pillar geometry ( i.e. the pillar size, the ratio of pillar height to width and the taper), the slip plane orientation and so on.

由于基座和刚性压头的约束作用，微柱的尺度效应强烈地依赖于微柱几何（宽度、高宽比、锥度）和滑移面取向角等多种因素。