target density的例句大全

Introducing azimuth and radial integrated coefficients, estimation formula of vertical target density with miss projectile is derived.

引入方位系数和径向综合系数，推导出了有脱靶弹的立靶密集度估计公式。

This calculation method can provide theoretical and engineering practice reference for vertical target density estimation of automatic gun with a few miss projectiles.

该计算方法可以为少量脱靶弹存在时自动火炮立靶密集度估计问题提供理论与工程实践的参考。

The three dimension temperature distribution along mid-plane during hot pressing, the effect of moisture content and target density of mat on the distribution, the flow vapor pressure and the effect on the forming mechanism on density.

热压过程中板坯中平面温度场的分布。主要研究了不同条件下刨花板坯整个热压过程中中平面温度场的实时分布情况，水蒸气的流向以及成板密度形成机理的影响。

When target density is high, the dynamic WTA method is adopted to carry out firepower distribution.

目标密度较大，则应采用动态WTA方法进行火力分配。

According to the experimental data, the effects of steam pressure, target thickness, target density, temperature and moisture content of mat on the time were evaluated. Some basic laws of steam-injection hot-pressing heat and matter conduction of middle and low density fiberboard were summarized.

分析蒸汽压力、目标厚度、目标密度、热压温度及板坯含水率对其影响，得出了中低密度纤维板喷蒸热压传热传质的基本规律。

During the stage of a rapidly increasing temperature, four main factors ( MC, the temperature of hot-plates, target density and thickness) affect temperature and gas changes, and gas pressure of core is ascending;

快速升温段：四个主要因素（热压温度、含水率、目标密度和目标厚度）对温度和气压的变化有着一定的影响，中心气压是上升的；

In vertical target density test, processing for miss projectile does not form consistent common understanding and treatment method.

自动火炮立靶密集度试验对脱靶弹的处理尚未形成较为一致的共识和处理方法。

The spherical powder product is obtained with particle size about 0.05 μ m and well-distributed, excellent flowability and suitable for preparation of ITO target material with high density.

产品平均粒径0.05μm左右，颗粒为球形，分布较均匀，流动性好，适于制备高密度的ITO靶材。

Some different thickness aluminum reflective films were produced on silicon substrate by using the electron-beam evaporation method and high purity aluminum target. The reflectivity curves of Al film in the visible light region were measured, the density and conductivity of films were analyzed.

采用电子束蒸发的方法，以高纯度的Al为靶材，硅片为衬底，制备了不同厚度的Al反射膜，并测量了在可见光范围内反射率曲线，分析了薄膜的致密性和电导率。

The application of the single-ground-motion analysis method shall meet the requirements of envelop of the power spectral density as well as fitting of the target response spectrum.

采用单组人工时程分析法不仅需要匹配目标反应谱，而且要满足功率谱密度的包络要求。

It ′ s different from traditional methods of covering hole and projecting target sheet. It uses CCD to grasp facula confirms its centre and radius by analyzing distribution of laser energy density and calculate the result.

区别于传统的套孔法和反射靶板法，该方法通过CCD采集激光光斑，用质心法确定光斑中心，根据激光能量密度分布确定激光光斑半径，进而计算出待测的激光束散角。

Besides, the bubble density and reflectance increased with the wake observation position approaching the target ship.

同时，随着观测点在尾迹中的位置距目标船的接近，气泡密度不断增大，反射率也随之增强。

With low density discretization, the first stage optimization could seek energy-saving target speed curve widely and provide optimized guidance for the second.

第一阶段优化采用低密度离散化方式，全面搜索可行的节能目标速度曲线，为第二阶段优化提供优化指导。

Based on the estimation of the clutter density in real time, the algorithm can get more accurate estimation of the target state.

针对这一问题，提出了一种修正的联合概率数据互联算法，该算法通过实时地调整这一参数来获得对目标较为准确的估计结果。

The effect of projectile density, shapes, target thickness, projectile diameter, impact velocity and angles etc. on crater has been investigated.

研究了弹丸密度、弹丸形状、板厚度、弹丸速度、弹丸直径和弹丸撞击入射角等对靶成坑的影响。

Six weeks after the treatment, the target myocardial tissue sections were stained with hematoxylin/ eosin ( HE) and the capillary density was calculated.

治疗后6周，目标区心肌标本进行心肌微血管计数。

The target material used for video disk is liable to fracture in production, the higher the density, the stronger is the fracture tendency.

此光盘膜用靶材材料极易在制备过程中碎裂，并且密度越高，裂纹倾向越大。

It allows node to make worksheet by itself according to the nodes density and the coverage probability for the target area and carry it into effect in turn in order to lower energy-consumption and balance energy.

算法允许节点依据节点密度和目标区域覆盖概率要求自行确定其工作时刻表，实行轮换周期工作机制，从而实现降低能耗和均衡节点能量的目的。

Manufacture of ITO Target with High Density and High Conductivity

高密度高导电性ITO靶研制

The directive angle of normal acceleration is assumed to have uniform probability density function with variable mean in the interval of 2 π In order to be suitable for Track-While-Scan application it is assumed that only noisy position observation data of target are available.

法向加速度的方向角则假定在2π区间内具有均匀的概率密度。