temperature distortion的例句大全

Design and Development of Temperature Distortion Generator

温度畸变发生器研制

Blast furnace shell will get into plastic stress and temperature distortion, and then thermal elasticity is inapplicability.

在炉壳温度较高或者炉内压力比较大的情况下炉壳会进入塑性变形状态，热弹性力学已不适用。

Chapter 2 study the temperature and heat distortion, using finite element software to analysis GMA temperature field and the heat distortion.

第二章研究了GMA的温度场和热变形，使用有限元软件对GMA温度场及热变形进行了分析。

The measuring of temperature change and distortion in RTM moulds shows that the exothermic peak of resin in the cavity can be adjusted through catalyst contents. The cracking and softening of surface resins result in the mould failure.

RTM模腔内温度变化与形变的测试结果表明：模腔内树脂的放热峰可以通过改变固化剂的含量适当调节，模腔表面胶衣及表面层树脂应能承受120℃的热疲劳冲击；

The transient temperature distribution and thermal distortion of optical coating components under an annular high-power continuous wave laser radiation

环状连续强激光下光学薄膜的瞬温和热畸变

Temperature Field and Thermal Distortion Field of Nd: YVO_4 Crystal with Double-Ends Pumping

双端泵浦Nd：YVO4晶体温度场及热形变场的研究

Fortunately the research method and obtained results have universality, which can be applied to analyze temperature field and thermal distortion field with axial symmetry thermal models.

研究方法和所得结论具有普适性，可以应用到其它具有轴对称性热模型产生的温度场、热形变分析工作中。

The dopants of Al_2O_3 greatly inhibited the increase of crystallite size and the phase transformation from tetragonal to monoclinic, also made the phase transformation temperature and crystal lattice distortion increase.

Al2O3的添加抑制了ZrO2（3Y）晶粒的增长和四方相向单斜相的结构相变，使相变温度显著提高，晶格畸变增大。

The space finite element analysis indicated that the prestressed concrete box girder's stress and the distortion are sensitive to the change of gradient of temperature pattern.

空间有限元分析表明，预应力混凝土箱梁的应力和变形对温度梯度模式的变化较为敏感。

The optimum conditions were discussed, stirring speed, temperature and adding sequence played critical roles during the process. Rare earth could lead to lattice distortion, increase lattice constant and achieve good magnetic properties and optimum doping amount was found.

讨论了最佳反应条件，搅拌速率、反应温度、加料顺序在形成纳米级粒子过程中起到关键作用；稀土掺杂能诱导晶胞畸变，使晶格常数增大，提高磁性能，实验得到了优选掺杂量。

But comparing to metal, owing to MC its low strength, modulus and heat distortion temperature, bad size stabilization, and high notch sensitivity, the usefulness of MC nylon is still limited.

然而与金属相比，MC尼龙存在强度、模量和热变形温度较低，尺寸稳定性差，对缺口冲击敏感，因而限制其应用的范围。

no color fading, no distortion, beautiful and practical appearance, over temperature automatic protection.

不变色 、 不变形美观实用,电机超温自动保护.

Dynamic mechanical analysis showed that the heat distortion resistance and the temperature of abrupt drop point for tensile modulus E ′ increased markedly with the irradiation dose.

动态力学分析（DMA）分析表明，聚己内酯辐照交联后的弹性模量和耐热性能显著提高。

Suitable amount of wood powder was also helpful for the increase of composite tensile modulus, flexural property and heat distortion temperature, while it might decrease the impact strength and tensile elongation.

适量木粉能提高复合材料的拉伸模量、弯曲性能和热变形温度，但材料的冲击强度和断裂伸长率有所降低。

Deformation determines recrystallization score when it has same deformation temperature and heat preservation time. Deformation in the materials produced more distortion and can increase the recrystallization driving.

变形温度和保温时间相同时，变形量的大小决定了再结晶分数的大小，变形量的增大使材料内部产生了更多的畸变能，使再结晶的驱动力增大。

Based on the analytic expressions of the IM products, intermodulation distortion ( IMD) sweet-spot and its dependencies on Taylor series coefficients, gate bias, drain bias, temperature, input signal levels and loads are analyzed.

根据二阶和三阶互调失真表达式，分析了互调失真抵消效应及其对泰勒级数系数的本征依赖性和对栅极偏置、漏极偏置、工作温度、输入信号功率大小及负载阻抗的外部依赖性。

Traditional analytical method establish model with shell unit, the method ignore the thermal distortion from temperature gradient.

而传统分析方法是按壳单元建立模型，忽略了温度梯度引起的热变形。

Simulation on the Response of A Single-stage Compressor to the Inlet Combined Distortion of Pressure and Temperature

某单级压气机对组合畸变响应特性的数值模拟

The results reveal that introducing bismaleimide into the cured system can improve the heat distortion temperature, flexural strength at high temperature and dielectric properties. In addition the reaction scheme of bismaleimide is mainly the self-polymerization but not copolymerization with epoxy group.

研究结果认为体系中引入双马来酰亚胺可提高热变形温度、热态强度和介电性能，双马来酰亚胺在固化中主要是自聚而不是和环氧基共聚。

Laser Welding Temperature Field and Workpiece Thermoelastic Distortion in SOA

SOA器件中激光焊接温度场与构件热弹性变形