temperature optimum的例句大全

Referring to the results of fixed-bed experiment, pyrolysis experiment is done by using the solid hot carrier pyrolysis technique developed by Dalian University of Technology ( DG coal pyrolysis process) to study the optimum temperature of pyrolysis and the products are analyzed.

以固定床热解实验的结果作为参考，进而对其进行大工固体热载体煤热解实验，考察采用DG技术进行热解的最佳温度，并对热解产物进行分析研究。

In this study, we sterilized bean curd crouton by the retort at high temperature and high pressure. The optimum sterilization conditions were 9 min-25 min-10 min/ 120 ℃.

试验用高温高压杀菌锅对油豆腐软罐头进行杀菌研究，确定其最佳杀菌工艺为120℃条件下9min-25min-10min。

The optimum pH and temperature were 8.2 and 30 ℃, respectively.

单级生物脱氮的最适pH和温度分别是82和30℃。

The optimum conditions of acylation was as follows: reaction temperature was 80~ 85 ℃.

在该路线中，双乙烯酮酯化反应的最佳反应条件为：反应温度为80~85℃；

This paper reports the production of zinc bromide from zinc cinder, and investigates the optimum process conditions of material ratio, pH value and reaction temperature.

研究了以锌渣为原料制备溴化锌工艺中原料配比、pH值、反应温度等工艺条件。

So critical temperature of strength decline, optimum amount of sand added to cement slurry, rule of properly controlling slurry properties and properly choosing additives are determined for Jiahua Class G Oilwell Cement.

从而达到实现确立嘉华G级油井水泥的强度衰退临界温度及合理加砂量、浆体性能的合理调控原则及外加剂的合理选配等目的。

Results The optimum forming technics could be seen as follows, the height of the drug storage tank was 3 cm, the temperature of drops was 80 ℃, the dropping distance was 5 cm and the temperature of the liquor condensate was 15 ℃.

结果：最佳成型工艺为贮药槽药液高度3cm、滴头温度80℃、滴距5cm、冷凝液温度15℃。

Gas residence time in water quencher is less than 1.5 s when temperature is 180 to 550 ℃; the optimum temperature in fabric filter is 120 to 150 ℃;

急冷装置在180～550℃时烟气停留时间应小于15s，布袋除尘器最佳工作温度为120～150℃；

Results: The optimum extraction conditions uere as follows: water sample ratio 1 ∶ 10 、 pH7.5 、 extaction temperature was 90 ℃、 one hour every time 、 ethanol concentration was 95%. made the experiment foundation for optimizing the extraction methods of Agrocybe cylindracea polysaccharides.

结果：提取茶树菇多糖的最佳工艺条件是浸提比1∶10、pH7.5、浸提温度90℃、浸提时间1h、乙醇浓度95%，为改善茶树菇多糖的提取方法提供了实验基础。

Using the contact temperature criterion of Block, the simulation results of the flash temperature and contact temperature of the meshing point are obtained, which provided scientific warranty for optimum design of gear transmission.

运用Block接触温度准则，得出齿轮各啮合点瞬现温升及接触温度变化的仿真分析结果，为齿轮传动结构的合理优化设计提供科学依据。

The results showed that the optimum conditions were: hydrochloric acid concentration 2.0%, hydrolysis temperature 80'C, and the concentration of tapioca starch 6g/ 100mL.

通过14（3~3）正交试验确定了木薯淀粉酸水解为还原性转化糖浆的理想条件：盐酸浓度2.0%（V／V），水解温度80℃，淀粉乳浓度6g／100mL。

Consideration from tar yield, 520 ℃ is the optimum temperature and this is consistent with the result of fixed-bed experiment.

从多产焦油的角度考虑，520℃为最佳热解温度，这与固定床热解实验得到的最佳热解温度相符合。

the properties of sucrase, immobilized in calcium alginate beads, were primarily studied. the results indicated that the optimum ph and temperature were 4.3 and 60 ℃ respectively for immobilized sucrase.

利用海藻酸钙凝胶球的包埋作用制备固定化蔗糖酶，并对其性质进行了初步研究，结果表明，游离酶被固定化后，最适pH值为4.0，最适温度为60℃。

the results indicate that the appropriate temperature for primordia and mycelial congeries formation is at 25-31 ℃ with the optimum temperature of 28 ℃.

结果表明，高温蘑菇菌丝聚集体和原基形成的适宜温度为25～31℃，最适温度为28℃；

the optimum seeking method of fluid's exit temperature during the design of heat exchanger

换热器设计中流体出口温度的优化选择

with favorable light and moisture conditions a plant grows at greatest rapidity if there is the optimum temperature for it.

在合适光照和水分条件下，如果有最适宜温度，则植物以最快速度生长。

optimum design for small high-low temperature test-box

小型高低温试验箱的优化设计

the optimum preparation conditions were determined as follows: mass ratio of natural graphite to sulfuric acid, nitric acid and decanol 1 ∶ 3 ∶ 2 ∶ 0.1, reaction time 40 min, and reaction temperature 60 ℃.

确定了可膨胀石墨的最佳制备条件：石墨与硫酸、硝酸、癸醇的质量比为1∶3∶2∶01，反应时间为40min，反应温度60℃。

optimum moisture content of rapeseed for ultradry storage at different temperature

油菜种子超干燥保存的最佳含水量研究

the optimum blanching temperature and time was 100 ℃ and 30 s, respectively.

在热烫加工中，选用了100℃、30s的工艺条件。