theoretical plate的例句大全

Flow field and structure in throttle orifice plate is systematically analyzed and studied by experiment and locale research, and finally theoretical foundation is provided for design of throttle equipment and test-bed on blower.

通过试验和现场调研，对节流孔板内的流场及结构等进行了系统地分析研究，最终为节流装置及风机试验台的设计提供理论依据。

Theoretical and experimental analysis of damping fish plate at rail joint

钢轨接头减振鱼尾板理论与试验分析

This research provides a theoretical method for design of a full column bolt with bottom plate.

此研究为带垫板全长锚杆支护设计提供一个理论计算方法。

The Theoretical Calculation and Its Experimental Verification of Airflow Layer Between Sliding Plate and Soil

滑板土壤间充气层的理论计算及其试验验证

We use a finite element method to study evolution of theoretical displacement, stress and strain field with a growing displacement applied at the remote plate ends, when fault slip and frictional stress are not given in advance but are determined in the solving process.

使用有限元素法研究了理论位移场、应力场和应变场随远场位移的演变情况。此时，断层位移和磨擦应力并不是预先给定而是在求解过程中同时确定的。

In theoretical analysis, Orthotropic plate theory was used for the hull bottom structure based on the elementary plate theory. The stiffness coefficients were derived.

在理论计算方面，首先应用板的基本理论对船底板架采用正交异性板理论，导出结构的刚度系数；

Objective To test the biomechanical properties of symphysis pubis diastasis fixed by cannulated screw or reconstruction plate and provide the theoretical basis for clinical practice.

目的对空心螺钉与重建钢板固定耻骨联合分离的生物力学性能进行测试，为临床应用提供理论依据。

Superharmonic resonance arisen in the nonlinear oscillator of simply supported rectangular thin plate subjected to a harmonic parametric excitation is investigated by theoretical analysis and experiments in the present work.

分析研究参数激励简支矩形薄板非线性振动中的超谐振动。

Theoretical Analysis and Experimental Study on Heat Transfer in Vacuum Plate Glass

真空平板玻璃传热理论分析及试验

In this paper, the maximum stress of the surface plate glass in container impacted inhorizonal direction is determined by theoretical analysis and experiments.

通过理论和实验的方法，分析集装箱中表面一块平板玻璃受到横向正面冲击的最大应力。

The shearing ability is improved by changing the shearing angle of the middle plate shear from 3 ° 30 ′ to 3 ° 45 ′, by theoretical analysis and the safety space of the shear is defined by simulation analysis.

通过理论分析，将某厂中板剪切机的剪刃倾角由3°30′改为3°45，′提高了剪切能力，并经过仿真分析确定了剪切机具有较大的安全裕量。

theoretical calculation method study on strength analysis of movable-plate of plane vulcanization machine

平板硫化机动模板强度分析的理论计算方法研究

by calculating, it is found that the equivalent single-layer plate theory can be applied to bamboo ribs tuss-ceramsite concrete sandwich panels, and the calculation results agree well with the experimental results, which provides a theoretical basis for the study and application of the new green wallboard.

通过计算发现等效单层板理论可应用于竹筋桁架-陶粒混凝土墙板，计算结果与试验结果吻合较好，为该类国内新型绿色墙板的研究、应用提供了理论依据。

The theoretical solution for rectangular thick plate with arbitrary boundary conditions is derived by symplectic geometry method.

利用辛几何法推导出了四边任意支承条件下矩形厚板弯曲的解析解。

theoretical analysis of polarization tracking based on half-wave plate

基于半波片的偏振跟踪理论分析

theoretical analyses show that the traditional flexural vibration of a slender rod and the stripe vibration mode of a rectangular thin plate are the limiting vibration modes of rectangular plates in flexural vibration, the results can be derived directly from the theory of this paper.

理论分析表明，经典的细棒弯曲振动理论以及矩形薄板的条纹振动模式，是弯曲振动矩形薄板的一些极限振动模式。

It can be used in theoretical inter-pretatio nand practical application of plate bending feasibility study.

从理论与实验两方面对冷热弯卷的可行性作了统一描述,这种方法是对该问题的理论解释和实际应用.

Modifying the yield line pattern in reference 〔 1 〕, a defect of the theoretical solution in reference 〔 1 〕 is mended, that is, with increasing the area of the steel plate, the load carrying capacity will increase to infinite.

改进了文献〔1〕的塑性铰线模式，修补了文献〔1〕的理论解的一个缺陷，即随着粘钢板的面积增加，承载力上升至无穷大。

By using the principle of air interlayer insulation, it is determined that the process for the insulation plate is a special forming process of air pocket through the theoretical calculation of insulation of maintaining structure composed of multi-layer homogeneous materials;

应用空气间层的保温与隔热原理，通过多层匀质材料组成的维护结构的传热方面的理论计算，确定了该保温板的制作工艺为特殊定做专用成型气袋施工法；

Study on the Graphic Method Used in Feed Proportioning for Rolling down of Bimetallic Composite Theoretical Analysis of Rolling-Force for Bimetal Composite Thin Plate

双金属复合轧制图解法配料的研究双金属复合带材轧制压力的理论分析