thickness的例句大全

The rhodium target, mass thickness is more than 150 mg/ cm 2, adapts to producing 103 Pd on Cyclone 30 accelerator.

确定了脉冲电镀工艺参数，成功地制备适用于生产103Pd的Cyclone30加速器照射用铑靶，镀层厚度大于150mg/cm2。

In addition, by the use of inversion software interpreted target area depth, thickness and resistivity quantitatively.

另外利用反演软件定量解释了目的层的深度、厚度及电阻率值。

The effects of experimental parameters including channel thickness, oxygen partial pressure, target composition and dielectric thickness on the electrical performances of IZO-TFTs were analyzed.

分析了沟道层厚度、溅射氧分压、靶材组分、介质层厚度等因素对铟锌氧化物薄膜晶体管（IZO-TFT）性能的影响，优化实验参数，改善器件性能。

Another, several parameters affecting spectral lines such as the x-rays tube voltage and x-ray tube target materials, target angle, target thickness, target radius are simulated through the established low-energy x-rays radiation device model.

另外通过建立的低能X射线辐射装置模型模拟了管电压及X光管的靶材料、靶角度、靶厚、靶半径等参数对能量谱线的影响。

The test results show that the residual speed of the penetrator drilling through target tended to slow down as the target thickness increased;

实验结果表明，随着靶板厚度的增加，穿过靶板弹体的剩余速度呈缓慢下降趋势；

The results show that the emission direction of the hot electrons at the rear side of the target shifts towards the target normal direction as the target thickness increases.

实验发现，随着靶厚度的增加，靶后超热电子的发射方向向靶的法线方向移动，同时电子束的发散角变大。

When the laser intensity irradiated on the target surface is about 1000W/ cm 2, the laser thermal stress descends rapidly with the increase of target thickness;

当照射靶面激光强度约1000W／cm2时，激光热应力随靶厚的增加而快速减小。

There was no association between targeted value of metabolic parameters, arterial intima-medial thickness and the two gene polymorphisms.

两基因多态性与各代谢指标干预1年达标情况和动脉内中膜厚度无相关关系（P>0.05）。

The Influence of Train Vibration Load and Spacing Layer Thickness on the Structural Stability

列车振动荷载及间隔土层厚度对结构稳定性的影响研究

The tearing modulus increases with the decrement of specimens thickness.

撕裂模量则随着试样厚度的减小而增加。

The results indicated the thickness, basic weight and tearing strength index of paper had no change;

结果表明，厚度、定量和抗张指数没有变化；

In China, the sectional thickness of primary component is restricted by "The Technical Criterion on Cold-formed Thin-wall Steel Structure".

我国现行《冷弯薄壁型钢结构技术规范》（GB50018-2002）对主要承重构件的截面厚度进行了限制，主要适用于仓库，厂房等公用建筑。

Technical measure of increasing thickness accuracy of hot rolled strip Steel

提高热轧带钢产品厚度精度的技术措施

Producing films of uniform thickness of paints and varnishes on test panel ( using spinner) Study on Technology and Optimization of Robotic Spray Painting

GB/T6741-1986均匀漆膜制备法（旋转涂漆器法）喷漆机器人喷漆工艺分析及优化研究

Experimental study on the swirling characteristics of a swirling water jet nozzle by using PIV Producing films of uniform thickness of paints and varnishes on test panel ( using spinner)

旋转射流喷嘴内旋流特性的PIV实验分析GB/T6741-1986均匀漆膜制备法（旋转涂漆器法）

Preparation of Catalysts by Spin-coating for Synthesis of Vertically Aligned Single-walled Carbon Nanotube Producing films of uniform thickness of paints and varnishes on test panel ( using spinner)

旋涂分布催化剂制备直立单壁碳纳米管GB/T6741-1986均匀漆膜制备法（旋转涂漆器法）

Test portion: Including to each kind of drive pipe in the different wall thickness, the different material, under in the different perforation parameter condition room experiments, the casing material, in the perforated zone rock mechanics performance room experiments;

试验部分：包括对各种套管在不同壁厚、不同材料、不同射孔参数条件下的室内试验，套管材料、射孔层段岩石的力学性能的室内试验；

Test Report on Determination of the Thickness of the Covering

确定覆盖层厚度的试验报告

Experiments comparing the measured value of ultrasonic thickness measurements and mechanical measurements on rough corroded materials without flattening the test surface were carried out. An average measurement error of from 0.6 mm to 2.2 mm was found in the ultrasonic measurements.

根据对未经平整的粗糙锈蚀表面分别进行超声波厚度测量和机械测量的比较试验，发现超声波测量的平均误差为0.6~2.2mm。

The weldability of 800 MPa high strength steel has been studied with 20 mm and 42 mm thickness plates by the maximum hardness test of heat-affected zone, Y slit cracking test and the test of weld energy input etc.

采用热影响区最高硬度试验、斜Y型坡口裂纹试验及焊接线能量的测试等手段研究了板厚分别为20mm及42mm的800MPa高强钢的焊接性。