threaded joint的例句大全

Application results of practical engineering prove that whole assembly control accuracy is improved. ( 4) Aiming at engineering application of automobile threaded joint assembly, network structure of assembly process control system based on distributed field bus is designed.

针对汽车螺纹联接装配的工程应用，实现了一种分布式总线装配过程控制系统的网络化结构。

The threaded joint assembly is a key technology and important process in automobile assembly manufacturing. Flexible assembly system of threaded joint is the main way to realize the complex threaded joint assembly process, improve assembly efficiency and ensure the quality of assembly.

螺纹联接的装配是汽车装配制造中的关键技术和重要工艺之一，螺纹联接柔性装配系统是实现复杂的螺纹联接装配工艺、提高装配效率和保证装配质量的主要方式。

When all threaded joint positions fit correctly and without tension, tighten all threaded joints according to the prescribed tightening torques.

当所有螺纹接头位置正确，且未承受张紧力时，则可以根据规定的拧紧力矩拧紧所有螺纹接头。

Pay particular attention to the threaded joint.

要特别注意螺纹接头。

If you find a leak, replace the affected threaded joint.

如果发现泄漏，则更换受影响的螺纹接头。

Detach the threaded joint by pulling it off the nipple.

从接头上拔下螺纹接头以分离该接头。

Danger of injury if threaded joint is incorrect.

螺纹接头不正确有人身伤害的危险。

Wishbone threaded joint on carrier side section.

托架侧面部分的叉杆式螺纹接头。

Influences of dimensional deviations on contact characteristics of threaded joint with double steps in drill collars

异径内外螺纹管接头钻铤双台阶螺纹接头尺寸偏差对接触特性的影响

In engineering application, selecting reasonable joint structure and prevent loosing method will effectively enhance the reliability of threaded joint.

指出了在工程上选用合理的联接结构和防松措施，可有效地提高螺纹联接的可靠性。

Install toe eccentric threaded joint between transverse strut and rear-axle carrier side section.

安装横向支柱和后轴托架侧梁之间的偏心螺纹接头。

A new seal structure suited to solid rocket motors ( SRM) is introduced, and threaded joint structures and sealing glue compound are studied.

提出了一种适用于固体火箭发动机（SRM）的新型密封结构，并对应用于特定尺寸的螺纹联接结构方式、胶种选择进行了研究。

Loosen the safety-related threaded joint.

松开起安全作用的螺纹接头。

Based on pressure and high low temperature cycling tests and theoretic analysis, the threaded joint parts filled with sealing glue compound show excellent seal ability, and can be applied to SRM.

通过压力、高低温循环等大量的试验和理论分析表明：采用填充密封胶的螺纹联接密封结构具有优异的密封性，适宜在固体火箭发动机环境中应用。

Transition fittings are available for adapting to new or existing threaded or solder joint ends.

还可提供转换管件,用于适配新的或现存的螺纹或焊料连接端口.

Assembly consists of thumb screw, hooks, swivel joint, and stem, threaded at one end.

这种总成由翼型螺丝、钩、转接头和杆子组成，在一端上有螺纹。

Vertical Bearing Capacity Behavior of Roll Forming Screw Pile; Assembly consists of thumb screw, hooks, swivel joint, and stem, threaded at one end.

滚压成型螺纹灌注桩竖向承载力性能研究这种总成由翼型螺丝、钩、转接头和杆子组成，在一端上有螺纹。

ball valves threaded, socket-welding, solder joint, grooved and flared ends.

球阀螺纹，承插焊接，焊接连接，带槽和扩口连接。

mss sp-110 covers ball valves, threaded, socket-welding, solder joint, grooved and flared ends.

110包括球阀，螺纹、承插焊、焊接、卡箍和扩口连接。

Vertically threaded reinforcements socket joint technology

直螺纹钢筋接头连接技术