through crack的例句大全

In this paper, the fracture character and cause were analyzed through crack macroscopic observation, fracture surfaces observation of cracks, metallography analysis and material mechanics properties testing.

通过对故障油箱壁板的裂纹宏观观察、断口的宏微观观察以及裂纹金相分析和材料的性能测试，对壁板裂纹的性质与原因进行了分析。

Investigation done in this paper is the retardation effect of a single tensile overloading on the fatigue crack growth rate of on axial through crack in 16 Mn steel pressure vessels.

本文对16Mn钢压力容器中轴向贯穿疲劳裂纹的超载迟滞效应进行了试验研究。

Based on this, the equivalent COD conversion relation between a yielded surface crack in an general oblate shell and a through crack in an infinite plate is derived.

在此基础上，提出了屈服后一般扁壳表面裂纹与平板穿透裂纹的等COD换算方法。

Complex function theory is, so far, only method that has been used to solve the plane problems in homogeneous anisotropic elastic body with a center through crack, as in reference [ 1].

带中心穿透裂纹的各向异性体均质模型的平面问题迄今仅见于复变函数方法的求解，如文献[1]。

Using MARC commercial software, tensile plate models of both all base steel and welded joint with various center through crack sizes were computed by three-dimensional finite element method, and the tensile process was simulated at the same time.

采用MARC商用软件，对不同中心贯穿裂纹尺寸的母材及其实际焊接接头拉伸板模型进行了三维有限元计算和拉伸过程模拟。

The experiment results demonstrate that the failure process of thermal barrier coating mainly goes through crack formation, propagation and spallation of coating, whereas, the oxidation of bond coat is the main cause of coating spallation.

实验表明热障涂层热震失效的过程主要是裂纹形成、扩展及涂层剥落，粘结层的氧化是导致涂层剥落失效的重要原因。

We wormed our way through the crack in the wall.

我们慢慢地从墙上的裂缝处爬出来。

Arresting and Reinforcing of Grinding Crack through Pulse Current Discharge

磨削裂纹的脉冲放电止裂与强化

Through the actual mix design test of mass concrete for the Badong Yangtze Bridge pile-cap, this article elaborated on the procedure of the mix design of mass anti-crack concrete and the theoretical foundations of the choice of concrete's raw materials in detail.

通过巴东长江大桥承台大体积混凝土配合比试验实例，给出了大体积防裂混凝土配合比的设计思路和原材料选择的理论依据。

The principle and method for testing surface crack through direct current potential difference are introduced.

首先介绍了直流电位法&裂纹扩展片检测裂纹的方法和原理。

Write the name down so that you remember or it'll slip through the crack.

将名字写下来，那样你会记住，否则它会被忘记的。

Nearly 80 percent of the coolant channels are filled with supercritical kerosene while about 60 percent of it are in thermal crack region. About 30 percent of the heat transfer rate is absorbed by kerosene through thermal crack.

研究发现：冷却通道长度的80%中煤油处于超临界状态，60%处于裂解区，通过裂解吸收了约30%的热量。

Through comparison with three dimension single notch compact tension specimen, effect of inclined crack plane and different angle loading to SIF and SERR of crack tip is analyzed and summarized.

通过与三维单边直裂纹的紧凑拉伸试样进行比较，分析并总结倾斜裂纹面及复合加载对裂纹尖端应力强度因子和能量释放率的影响。

Plenty of oxidation etching pits are found on the surface of the specimen after the thermal fatigue test, and the surface principal crack is prone to propagate through these etching pits.

实验结果发现，试样表面出现大量的氧化腐蚀坑，表面主裂纹优先通过这些腐蚀坑扩展。

Through analysis on the failure specimen of automobile brake drum the reasons to failure are as follows: ( 1) The hardness and strength of brake drum is not high enough so that grinding trace and crack of axis direction appear.

通过对失效的江淮某汽车制动鼓取样分析，其失效原因：①材料强度、硬度过低，制动鼓出现磨痕台阶和轴向裂纹；

" You see a tiny crack in the door, and you have to run through it," she says.

既然你已经看到地板上的一道小裂缝了，就不得不钻进去看个究竟。

Through the research of factors affecting the quantity of water flow in cracks, the authors plot the relation curve between unit water flow and width of crack and obtain the time and the width of cracks which maybe lead to the self-heal of concrete cracks.

通过对混凝土裂缝渗水量影响因素的研究，确定了单位渗水量与裂缝宽度等的关系曲线，以及混凝土裂缝可能产生自愈合的时间及裂缝宽度；

According to the temperature boundary conditions which were tested when the crack begins to propagate in the experiments, the thermal fracture toughness ( thermal KIC) can be obtained through the corresponding calculation by the boundary element method.

根据实验测得的裂缝扩展时的温度边界条件，结合边界元数值计算，可获得混凝土、砂浆的温度断裂韧性。

Through the welding crack test of inclined Y groove, physical inspection of mechanical property of welded joint, etc, the steel plate quality and welding process were reviewed as well.

通过斜Y坡口焊接裂纹试验、实物焊接接头的力学性能检验等方法，评价了钢板的质量和焊接工艺。

The super high speed impact quenching was studied with experiment of crack arresting through pulse current discharge.

通过脉冲放电止裂试验研究了裂尖超高速淬火全过程。