tolerances的例句大全

Scholars of behavioral economics, including Dr. Kahneman, have attempted to tease out the factors behind individuals 'and investors' shifting risk tolerances and decisions.

包括卡内曼博士在内，行为经济学的学者曾尝试理出个人及投资者的风险容忍度和决策不断变化背后的因素。

To have an interference or force fit between mating parts, the tolerances must be such as to create a zero or negative allowance.

为了使配合零件之间具有过盈或强制配合，公差必须产生零或负允差。

Crop Salt Tolerances and its management of irrigation with saline water

作物的耐盐性及盐水灌溉管理

Study of Integrated Information System for Geometrical Tolerances in the New-generation GPS Based on Category Theory

基于范畴论的产品形位几何规范信息集成系统研究

At the last of this section, the error tolerances of multi-peaks filter and EDFA gain flatting filter are also analyzed.

最后还分析了多峰滤光片和增益平滑滤光片的容差特性。

KEF analyzed the effect of component tolerances on the overall response and found that by tightening these in the most critical areas an improvement in consistency could be achieved.

KEF从整个响应频段分析了组件的误差值后，发现在最关键的一些地方缩小误差的容许值，可以改进其一致性。

This paper analyses the impact of the magnitude, phase and installation position tolerances on sidelobe of shaped-beam pattern using a normal distribution with zero mean as error mode.

文中以均值为零的正态分布作为误差模型，分别就幅度、相位以及安装位置公差对赋形方向图副瓣带来的影响进行了统计分析。

TechCrunch has noted that the two to three percent difference in battery performance is within the manufacturing tolerances for any device.

TechCrunch提示，对于任何设备而言，2%-3%的电池寿命差异都在加工误差的允许范围内。

Conclusions: Some tolerances to chemotherapeutics increase during the oncogenesis process of breast carcinoma. MDR1/ P-gp and OPN is associated with the intrinsic MDR in breast carcinoma.

结论：部分乳腺癌细胞在发生发展的过程中同时伴有对化疗药物耐受能力的增加，MDR1/P-gp和OPN均与乳腺癌的内源性耐药相关；

Relevant process testing showed that when threading the non-coupled end of a coupled tubing, thread quality was negatively affected little by the coupling, and that all the items inspected, namely taper, pitch, tooth height, standoff and L4 were within the specific tolerances.

工艺试验表明，带接箍油管另一端加工螺纹时，其接箍对螺纹质量基本无影响，其检验项目锥度、螺距、齿高、紧密距、L4长度均在公差允许范围内。

Reduced contact force due to temperature effect and control module tolerances.

由于温度效应和控制单元公差导致的接触力降低。

Research on Effects of Tolerances on Contact Force of Trochoid Transmission

误差因素对摆线针轮传动齿面载荷的影响研究

Spherical plain bearing rod ends-Boundary dimensions and tolerances Exterior measurement includes specification and size, surface defect, and sewing requirement.

GB/T4222-1991杆端关节轴承外形尺寸和公差外视质量包括规格尺寸及公差、面疵点。

steel die forgings - tolerances on dimensions - part 2 : upset forging made on horizontal forging machines.

钢热模锻件.尺寸公差.第2部分：在水平锻造机器上的顶锻

numerical examples are given for the broadside array in which the excitation amplitude coefficients have tolerances.

并对激励幅度具有容差的侧射天线阵进行了计算。

With gadgets getting smaller and smaller, dimensional tolerances are getting smaller and smaller;

随着要做的小工具变得越来越小，尺寸公差越来越小；

aerospace fitting joint assembly, radial sealing. internal thread bosses. iso metric thread profile and tolerances. dimensions.

航空和航天。经向密封接头。阴螺纹剖面和ISO米制螺纹公差。尺寸。

screwed sealing plugs, radial sealing. iso metric thread profile and tolerances.

径向封塞.ISO米制螺纹剖面和公差

fluid power systems and components - cylinder-rod wiper-ring housings in reciprocating applications - dimensions and tolerances

流体动力系统和件.往复作用的活塞杆刮垢环罩.尺寸和公差

find indusium window offset big products need to test several confirmation, beyond the tolerances products rejected processing;

发现覆盖膜开窗偏移大的产品需要测数确认，超出公差范围的产品报废处理；