tool face的例句大全

changing the tool face angle of the measuring rod to obtain the flat that the magnetic rod and the measuring rod co-located on;

通过改变所述测量杆的工具面向角，获得所述磁力杆和所述测量杆共同所在的平面；

The research result in the paper shows that accurate tool face angle can still be obtained under this circumstance.

研究表明，即使在这种情况下，完全可以求得准确的工具面角；

The main function of the inclinometer is to measure the angle of inclination 、 azimuth and tool face angle.

随钻测斜仪的主要作用是完成井斜角、方位角、工具面角等参数的测量。

continuous chip. the continuous chip is characterized by a general flow of the separated metal along the tool face.

连续的切屑一般具有分离金属沿刀具面流动的特征。

The flat tool face points upwards.

平的工具面朝上。

Electronic directional drilling system consists of downhole tool and sur-face data processing equipment.

电子式定向仪由井下仪器及地面处理设备组成。

Using the lasso tool I chose the areas of her face I wanted to blur

我使用套索工具选择我想要的她的面部的区域然后加以模糊

The tooth profile precision of carbon alloy slotting tool with cone rake face is analyzed, the carbon alloy slotting tool with convex rake face is put forward and compared with the slotting tool with cone rake face.

分析了锥形前刀面硬质合金插齿刀齿形误差，提出一种凸曲前刀面硬质合金插齿刀并对二者的齿形精度进行了比较。

Moving coordinate system for grinding the rake face of end mill using a spherical wheel Shaping and planing produce flat surfaces with a single-point cutting tool.

构建球面砂轮磨削立铣刀前刀面的游动坐标系仿型刨削和牛头刨削用单刃刀具加工平面。

Tool selection is a key problem that influence part face quality and process cost in CAPP system.

刀具选择是影响CAPP系统中工件表面质量和加工成本的关键环节，而刀具优化配置也是车间资源中最为复杂和具有柔性的一部分。

Automatic machine tool for turning double end face of the piston pin The hardness range and difference of hardness and grit of the two grinding wheels for unequal double end griding of bearing sealing seat.

车活塞销双端面自动机床通过对砂轮性能的实际检测、质量跟踪及磨削试验，得出轴承密封座双端面不等面磨削所使用砂轮的硬度范围、两侧砂轮的硬度差及砂轮粒度等数据。

The old tool carriage with point contact crop appearance for steel pipes is not suitable to cut the oblique end face on pipes because of tool edge bluntness and lower tool service life.

传统的钢管平头方式&点接触平头方式设计的刀盘，对于切斜的管端面很不适应，易打钝刃口，降低刀具使用寿命；

As the tool softens due to heat, it wears and Breaks down at the cutting edge or face. Don't mess around with sharp knives!

在刃口因高温而软化的同时，刀具刃口便开始磨耗并损坏。不要摆弄刀口锋利的刀！

Tangential motion along grinding wheel face is achieved by the length feed of the lathe working table, and normal motion jiggle inputting along grinding wheel face is achieved by the minute displacement mechanism of the dressing tool.

其中沿砂轮表面切向运动由机床工作台的纵向进给运动完成，而沿砂轮表面法向运动的微进给运动由修整器的微位移机构来实现。

The double-faces stresses ( vertical and tangential stress) of the measuring tool in the hardness experiments, especially the vertical pressure, are accounted for.

研究中计及了硬度实验中压头下的双向压力（垂直和切向压力）对其硬度的影响，尤其是垂直压力的影响。

special machine tool of double side face process for spherical head pin

球头销双端面加工专用机床

in case of interrupted cutting, breakage of the flank face may be the tool failure criterion.

本实验所用的断续条件下，刀具的失效判据为崩刃。

It introduces the development history of the Computer Aided Process Planning and analyzes its domestic and international application status together with its future development trend. The development trend of the future CAPP will necessarily face development in a few directions in terms of integration, tool and intelligence etc.

介绍了计算机辅助工艺的发展历史，分析了其应用的国内外现状和其未来的发展趋势，未来CAPP的发展趋势必将向集成化、工具化和智能化几个方向进一步发展。

Machine-tools. Spindle noses and face plates . Sizes for interchangeability. Part 2: camlock type.

车床切削工具. 轴头和面板. 可互换性尺寸. 第2部分: 凸轮锁型.

The razor processing of the inner hole outer circle and the end face of the work piece can be carried out simultaneously only requiring a cutting tool and two arbors.

只需用一把刀具、二把刀杆就可同时进行工件的内孔外圆和端面的精剃加工。