tooth gear的例句大全

Tooth surface equations of the variable tooth thickness plane worm gear transmission are deduced based on the theory of engagement.

利用啮合原理的知识，笔者推导出变齿厚平面蜗轮传动副的齿面方程。

The QX straight conjugate internal gear pump is a new type of hydraulically driving element. The calculation of tooth profile, the limiting point of meshing, the designing process of slotting cutter were introduced.

介绍了一种新型液压动力元件&QX型直线共轭内啮合齿轮泵的齿廓曲线计算、专用插齿刀具设计方法，分析了齿廓啮合极限点。

Through analyzing effect of friction of tooth surface on reactive force of gear support abutment, this article shows that friction of tooth surface is a factor that causes forced vibration of gear support abutment, which is not ignored.

分析了齿面摩擦力对齿轮支座反力的影响。表明齿面摩擦力是影响齿轮支座强迫振动不容忽视的一个因素。

Building the parametric model of straight-tooth bevel gear wheel with CATIA is discussed.

利用CATIA的混合建模功能在实体和曲面工作台上建立直齿圆锥齿轮模型，并通过知识工程工作台完成齿轮的参数化建模。

The normal lines of the cam pitch curve at the meshing points intersect at the instantaneous center of the cam and the pin gear, which accords with the meshing principle of tooth contour.

在凸轮与针轮啮合的瞬时，各针齿与凸轮啮合点处，凸轮理论廓线的法线交汇于该瞬时凸轮与针轮的速度瞬心，符合齿形啮合基本定理。

In addition, the tooth profile of spiral bevel gear is spherical involute and the tooth surface is irregular space curved face which make it difficult to establish the accurate 3D models. The simulation analysis of meshing and optimization design of spiral bevel gears is greatly hindered.

同时弧齿锥齿轮齿廓形状为复杂的球面渐开线，齿面也为不规则的空间曲面，三维几何精确建模较为困难，导致其啮合仿真分析以及局部优化设计的相关研究工作难以开展和深入。

Spiral angle and tooth width of gear in oil pump

油泵齿轮的螺旋角和齿宽

Calculation of Pressure Angle and Spiral Angle on Spiral Bevel Gear Tooth Surface

螺旋伞齿轮齿面上指定点处压力角及螺旋角的计算

Design and Performance Test of Spiral Bevel Gear with Long Tooth Height

高齿弧齿锥齿轮的设计与性能试验

The optimal design of spiral bevel gear with high tooth based on genetic algorithm

基于遗传算法的高齿弧齿锥齿轮优化设计

Study on Generating Pinholes of Pin Gear Housing Using Circular Tooth Slotter

用圆弧齿插刀展成针轮销孔的几个技术问题

Secondly, as a result of tooth thickness in the direction of tooth wear, so that active and passive gear mesh gap increased.

其次，由于轮齿在齿厚方向的磨损，使主、被动齿轮的啮合间隙增大。

The wear form of space gear mechanism in the vacuum environment was observed, and the degree of wear at the addendum, near the pitch and between the addendum and the tooth pitch, were analyzed by SEM.

采用扫描电镜分析了空间齿轮在真空环境下的磨损形式，同时分析了齿轮轮齿在齿顶、节圆附近以及齿顶和节圆之间的磨损程度。

Deviation of Addendum Circle and Its Influence on Thickness Measurement of Gear-tooth

齿顶圆偏差对齿厚测量的影响及修正

A Proof of Thinned Addendum Thickness of a Gear Tooth Generated with Positive Correction

正变位齿轮齿顶厚度必变小的证明

Tooth surface temperature and thermal equilibrium conditions have significant effects on gear performance and failure as well as lubrication system in high-speed gear transmissions for aerospace applications.

高速重载齿轮传动系统的热平衡状态以及轮齿表面温度的大小对齿轮传动的性能与失效以及齿轮润滑系统的设计与操作控制等有着重要的影响。

Gear grinding quality includes many contents. Here means primarily profile accuracy, tooth spacing accuracy, tooth flank roughness, flank grinding burn, and so on.

磨齿质量涉及内容广泛，这里主要指的是齿形精度、齿距精度、齿面粗糙度、齿面磨削烧伤等。

Formation spiral bevel gear has straight tooth profile and more teeth, and tooth grinding efficiency is low.

由于成形法螺旋锥齿轮的大轮具有直齿廓且齿数多，磨齿加工的效率低，因此，考虑对其采用高速切削加工的方法。

The radial runout of tooth ring of the coniflex gear, which is an important test item, is an important factor influencing the accumulated error of tooth spacing and the error of tooth spacing.

直齿锥齿轮的齿圈径向跳动是重要的检验项目，是影响齿距累积误差和齿距误差的重要因素。

Reverse idler gear shaft bearing Both gear centers have pinions with only half tooth.

回动空转齿轮轴轴承两个齿轮其中心都有一个小齿轮，这个小齿轮只有半边有齿轮。