transverse shear的例句大全

In chapter two, the governing equation of thermal buckling is established based on nonlinear geometry, the effects of transverse shear deformation are taken into accounted.

随后在几何非线性的基础上，考虑了横向剪切的影响，建立了复合材料层合扁球壳在均布荷载和温度场联合作用下的热屈曲控制方程。

The effect of transverse shear deformation is considered and angle of rotation of surface normal for each layer is different.

这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。

the effect of transverse shear and rotary inertia on wave propagation in an orthotropic piezoelectric laminated cylindrical shell was studied in this paper.

研究了考虑横向剪切及转动惯量效应影响的正交各向异性压电层合壳中的波传播规律。

Based on the Reissner Mindlin type global displacement field and predictor corrector method, the deflections and transverse shear stresses were investigated for laminated composite cylindrical shells under mechanical load.

本文根据Reissner Mindlin型的全局位移场（一阶和三阶），应用有限元预测&修正法，数值计算和分析了机械载荷作用下复合材料层合圆柱壳的挠度和横向剪应力。

The existing anchorage system for prestressed tendons and cables of steel is no longer appropriate for that of FRP due to their low transverse shear strength and crushing resistance.

但其横向抗剪及抗挤压强度较低，现有的预应力筋和拉索锚具体系不再适用于FRP预应力筋和拉索。

This paper presents a method to identify transverse shear modulus for composite materials.

本文提出一种测试复合材料横向剪切弹性模量的参数识别方法.

At the same time introduce a bar element which considered the transverse shear effect. Compared the two bar elements to see the improvement of the tunnel stability after considering the transverse shear effect of the bolt.

同时引入了一种考虑横向剪切作用的杆单元，与以往的杆单元进行对比，得出在考虑横向剪切作用后，锚杆对稳定性的提升效果。

among all parameters, pin insertion angle, pin diameter and pin density are primary for compression and shear properties, while the oblique angle and pin layout could be neglected except that pins on transverse plane about shearing load have little contribution to the shear behavior.

Pin植入角、直径以及植入密度是压缩和剪切性能的主要影响因素，而端部斜切角及空间布局的影响可忽略。此外，横向面内pin对剪切性能的贡献较小。

The parameters in the aeries include: amount of longitudinal reinforcement, amount of transverse reinforcement, shear span-to-depth ratio, thickness of tube wall and strength of concrete.

试验中的主要参数有：纵向钢筋的数量、横向配筋率、剪跨比、管壁的厚度及混凝土强度。

In this paper, an improved shell theory is employed to analyze the free vibrations of a spherically isotropic spherical shell submerged in a compressible fluid medium. The effects of shear deformation, rotary inertia and transverse normal strain are included.

采用六模态的中厚壳理论研究了可压缩流体中球面各向同性球壳的自由振动，即在分析中考虑了剪切变形，旋转惯量和横向正应变的影响。

in addition, shear stresses in both the transverse and longitudinal directions exist.

另外, 在横向上纵向上都存在剪切应力的分布.

the main results show: the ratios of the horizontal axial projected length of strengthening stage of skeleton curves of specimens to the yielding displacements are directly proportional to the transverse reinforcement characteristic values and inversely proportional to the axial compressive ratios and shear span ratios;

研究表明：轴压比超限时试验骨架曲线强化段在水平轴上的投影长度和屈服位移的比值与配箍特征值成正比，与轴压比和剪跨比成反比；

Considering the change of the load transverse distribution coefficient along the bridge span, the maximum value of shear force at supporting point caused by uniformly distributed lane load is calculated by integral method.

考虑荷载横向分布系数m沿桥跨方向的变化，采用积分法对车道均布荷载引起的支点最大剪力进行了计算。

Study on setting of initial shear stiffness of LRB in seismic-isolation design The Seismic Response of LRB Isolation Bridges under Transverse Earthquake

隔震设计中铅芯橡胶支座（LRB）屈服前刚度取值的研究铅芯橡胶支座隔震桥梁横向地震反应分析

The transverse weld topography, the connect width between plates and tension and shear load were analyzed when the incident angle changed.

分析了入射角改变对焊接件外观形貌、焊缝截面、焊缝板间连接宽度以及所承受的拉剪载荷的影响。

this thesis presents "illustration method" which describes the shear lag effect of main girder with single box and triple-celled by the shear lag coefficient curve illustration and transverse distribution chart of longitudinal stress.

提出了一种用截面剪力滞系数曲线图或纵向应力沿横截面分布图来描述单箱三室（或多室）主梁剪力滞效应的图示法；

results the transverse strength and shear strength were increased with the increase of the carbon fiber content.

结果随着碳纤维含量的增加，根管桩的弯曲强度和剪切强度均逐渐增加。