valve set的例句大全

are cargo tank relief valves set correctly and actual relief valve settings clearly and visibly displayed?

货舱安全阀的设定位置是否正确,安全阀实际定位的显示是否清楚和直观?

There are valve dither and valve set point circuit to improve the performance of the system.

为改善伺服阀的特性,在系统各通道的伺服输出电路中增加了可程控的阀偏置和阀颤振电路.

The functions of portable data recorder for adjusting test of safety valves are introduced, the testing data are collected, treated and typed in time, and then the sampling differentiation conditions of safety valve set and reseat pressures are discussed, the optimum programm is determined.

介绍便携式安全阀调整试验用数据记录仪的功能，对试验数据进行实时采集、处理和打印试验记录等，并对安全阀起跳压力和回座压力采样的判别条件进行了讨论，确定了最佳方案。

It has replaced the manifold and electrical three-way ball valve set in the old-fashioned metering station and it applies not only to thin oil medium but also to heavy oil medium.

它代替了老式计量站中的管汇及电动三通球阀阀组，既适用于稀油介质，也适用于稠油介质。

Overvoltage Breakdown of Horizontal Output Valve in Color TV Set: Parallel-Connected Capacitance Method for Diagnosis and Theoretical Analysis Thereabout

逆程电容法对彩电行管过压击穿诊断及其分析

Before taking a flow measurement reading, set the valve to its fully open ( 4.0) or at a preset position.

在获取流量测量读数之前，将阀门设置在全开（4.0）或在一个预调的位置。

When heat tempera-ture exceeds the highest temperature pre-set, temperature control instrument con-trol relay close to open water control electromagnetic valve for cooling treatment.

当加热温度超过预先设定的最高温度值时，通过温控仪控制继电器的闭合打开水路控制电磁阀进行冷却降温处理。

A test rig is set up and the experiment on the valve is carried out at the room temperature and high temperature. The experimental proportional characteristics are obtained and compared with the simulation results.

搭建了试验台，分别在常温与高温条件下进行阀的特性试验研究，给出了比例阀的比例特性曲线，并与仿真结果进行了比较。

In this thesis, the system with thermal expansion valve and capillary as first throttling device has been studied. A thermostatic laboratory and an air-source heat pump system of two-stage cycle with flash tank have been set up in this thesis.

本文通过实验和模拟的方法对热力膨胀阀和毛细管作为第一级节流机构的系统进行了研究。

Above valve mouth in, pull out, give vent to anger door needle, set free to the limit;

固克特补胎液气门嘴处于上方，拔出气门针，余气放尽；

The arrangement of the safety valve makes the barrel body form zero load when the tyre pressure reaches the set value.

设置安全阀可使得在轮胎压力达到设定值时，筒体形成空载。

Inlet valve, supplying valve and water level sensor are installed in close to the upper and lower edges of tank. Differently cleaning valve is deviced with curtain structure, the ingenious set of these valves can achieve the best beneficial cleaning effects.

进水阀、供水阀及水位传感器设置在接近于水箱的上下边缘位置，清洗阀采用水幕槽结构，这些阀门的巧妙设置有利于整个水箱的清洗效果。

Study on set pressure of discharge safety relief valve of reciprocating compressor

往复式压缩机出口泄压安全阀整定压力的探讨

The heat-supply system with distributed variable frequency pump is a heat-supply system in which the flow rate is regulated with return-water pressured pump, instead of valve, set at return water pipe on the high-temperature side of heat exchange in substation.

分布式变频泵供热系统是指在热力站换热器一次侧回水管上设置回水加压泵，代替阀门完成流量调节的供热系统。

Based on the theory of auto disturbance rejection control ( ADRC) and inverse system nonlinear control, three different control schemes for hydroturbine generator set were designed, each of which included water valve control and excitation control.

基于水轮发电机组刚性水击模型，分别采用逆系统非线性控制和自抗扰控制（ADRC）方法，设计了水门和励磁控制系统。

Water overflow in the top of tank combined with fixed water gun is suitable for fixed storage tank, and the safe valve with appropriate size shall be set simultaneously.

对于固定式储罐，建议采用储罐顶部水漫流冷却和固定水炮相结合的方式，同时应设置大小合适的安全阀；

The simulation of LO_2 tank pressurization system indicates that PID control parameters should be set reasonably and the initial opening of pneumatic diaphragm control valve should be adjusted to nominal pressurant mass rate, which is effective to improve stability of pressurization starting transient.

对贮箱增压系统的仿真表明，合理设计PID控制参数并根据经验预置与额定流量相近的调节阀初始开度，对于提高增压系统起动过程的平稳性有利。

Pass the control toward the CO_2 dischargeses, the water current quantities, each electromagnetism valve etc, make the temperature that the water of the run off attains to set in advance.

通过对CO2流量、水流量、各电磁阀等的控制，使流出的水达到预先设定的温度。

Unclip tank vent valve and lines at the intake-air distributor and set them aside.

松开进气分配器处的油箱通风阀和管路，并将其放在一边。

adjust outlet gate valve to make it run within the set range of performance.

调节出水闸阀，使之在规定的性能范围内运转。