welded的例句大全

Orthogonal experiment design method is used to determine the optimum laser double-side welding parameters. The tensile strength of the retro-welding samples is used as the indicators of evaluating laser welding performance. The tensile and bending fatigue test are used to study the mechanical properties of welded joint.

选用正交试验设计方法确定Fe-Mn-Si形状记忆合金激光双面焊接的最佳工艺参数，以焊接后试样的抗拉强度作为评定焊接性能的指标。

Hydrogen embrittlement index ( 1%) of welds and heat affected zone ( HAZ) of C-Mn steel welded joints are studied by means of smooth and notched tensile specimen.

用光滑和缺口拉伸试件，对C-Mn钢的焊态和焊接热影响区的热模拟态进行氢脆敏感性指数的研究，并进行了金相与断口的SEM，TEM，AES的微区分析。

Based on the analysis of the fatigue notch factor of welded joints, the difference between the fatigue strength of welded joints under tension load and that under bending load is presented.

基于场强法理论得到的疲劳切口系数，有效的预测了焊接接头在承受拉伸载荷和弯曲载荷时的疲劳强度差异。

For a groove welded tension member in3/ 4 in. plate, what is the maximum size of fusion discontinuity permitted in astatically loaded member?

对于3/4英寸板材的受拉构件坡口焊缝，在承受静载荷时，熔合性缺陷允许的最大尺寸是多少？

By calculating, the maximum tension strain of the cold ribbed welded steel of the RC shear wall with confined boundary elements or with ordinary boundary elements is studied as the maximum compressive strain of concrete reaches its limited value.

计算分析了4片设有约束边缘构件和构造边缘构件的抗震墙边缘混凝土达到极限压应变时，竖向分布冷轧带肋钢筋的最大拉应变；

Bauschinger Effect in the Tension Test of Spiral Submerged-arc Welded Pipe

对影响管材屈服强度的包申格效应试验分析

Development of CAPP system for assembling welding process of welded structure

焊接结构件装焊CAPP系统的开发

The performance data of changing working conditionings mode and changing voltage and adjunctive heat transfer temperature difference and welded resistance and stray heat exchange and element ability step-down effect on the performance data of thermoelectric refrigerator are analyzed.

分析了热电制冷器的制冷工作特性、变工况特性和变电压特性，同时分析了附加传热温差、焊缝电阻、杂散热交换、元件性能下降对热电制冷器性能的影响。

A Study of Ultimate Bearing Capacity about Compression Member Welded with Thick Plank

厚板焊接压杆的极限承载力研究

The tension tests have been conducted for the materials of welding centre and heat affected zone, which come from welded joints in thick steel plate under two welding crafts.

对厚钢板两种焊接工艺焊接接头中的焊缝材料和热影响区材料进行拉伸试验。

It is very important to explore the influence of temperature on fracture toughness CTOD in welded joints of thick steel plate in the process of fabrication of modern huge steel structure.

大型厚壁钢结构建造中，研究温度对焊接接头断裂韧度的影响十分重要。

Annealing Quality Analysis and Control Measure of Stainless Thick Wall Welded Pipe

不锈钢薄壁焊管光亮退火质量分析及控制措施

Analysis of the Stress Distribution on Thick-wall Welded Tees by Three-Dimensional Finite Element Method

厚壁等径三通应力分布的有限元分析

The Elasto-Plastic Finite Element Analysis of Thick-Walled Cylinder Under Internal Pressure and Its Application to the Final Sizing Technology of Welded Pipe End

受内压厚壁圆筒的弹塑性有限元分析及其在焊管管端定径工艺中的应用

The movement of welding seams of tailor welded blanks combined by different material and different thick sheet metal is studied in this paper.

本文研究由不同材料和不同厚度板材组合的拼焊板方盒件在拉深成形中焊缝的移动。

Breakfast over, Aunt Polly had family worship: it began with a prayer built from the ground up of solid courses of scriptural quotations, welded together with a thin mortar of originality;

早饭过后，波莉姨妈做了祷告。开始的一篇祷告词完全是从《圣经》中引用来的，其中还掺杂着星星点点的新意。

Capacity Calculation of Welded Axially Compressed Members with Thin-Walled Box Section

焊接薄壁箱形截面轴心压杆的承载力计算

In the application process, welded thin-walled box section has a thin plate with broad width, and it is often difficult to guarantee local stability in performance.

在应用过程中，焊接薄壁箱形构件由于板宽壁薄，其局部稳定性能往往不易保证。

DISTORTIONAL BUCKLING BEHAVIOR OF HIGH STRENGTH COLD-FORMED STEEL COLUMNS SUBJECTED TO AXIAL COMPRESSION Capacity Calculation of Welded Axially Compressed Members with Thin-Walled Box Section

高强冷弯薄壁型钢轴压柱畸变屈曲研究焊接薄壁箱形截面轴心压杆的承载力计算

Steel has the advantage of high strength, light weight, good mechanical properties, etc., along with the development of steel structure, welded thin-walled box section member structure in more and more widely applied.

钢材具有强度高、质量轻、力学性能良好等优点，随着钢结构的发展，焊接薄壁箱形截面构件在越来越多的结构中得到了广泛的应用。