welding cycle的例句大全

For austenite hi-strength stainless steel, the tensile strength of resistance spot welding increases with the welding current and welding cycle under the condition of a constant pressure.

对奥氏体高强不锈钢而言，在压力一定时，电阻点焊拉伸强度随电流和焊接周波增加而增加。

A peak current of several thousand amperes flows during the welding cycle.

在焊接周期会产生几千安培的峰值电流.

The spot welding temperature field is calculated based on the ANSYS heat and electrical element; we received the heating characteristic and the thermal cycle curve of resistance spot welding.

基于ANSYS的热电单元计算了电阻点焊温度场，得到电阻点焊加热的特点和点焊热循环曲线。

Through impos-ing the boundary conditions in the temperature model, the heat source model of FSW was defined and the thermal cycle curve of the whole welding process was obtained.

在温度场模型中施加边界条件，确定搅拌摩擦焊热源模型，得到整个焊接过程中的热循环曲线，最高温度值均在各自的高塑性温度区间。

The instrument can acquire, process and display welding temperature, and can also give a printout of the welding thermal cycle curve arid characteristic parameters, the real time accurate measurement of welding thermal cycle is realized.

该测试仪可采集、处理和显示焊接温度信号，并可打印输出焊接热循环曲线及特征参数值，实现了焊接热循环的实时准确地测量。

Finally the influences of the power allocation among the wires on welding thermal cycle curve are discussed, and the results show that the power distribution among the wires of multi-wires LSAW will impact the highest temperature of the molten pool.

最后，探讨了焊丝之间的功率分配对焊接热循环曲线的影响，研究发现：多丝埋弧焊焊丝之间的功率分配会对熔池最高温度产生影响。

A Study on Intelligent Welding Thermal Cycle Measuring Instrument

智能式焊接热循环测试仪的研究

Design and data process of data acquisition system for welding thermal cycle

焊接热循环数据采集系统的设计与数据处理

Welding Thermal Cycle Testing System Based on Virtual Instrument

基于虚拟仪器的焊接热循环测试系统

Calculation and detection of thermal cycle of laser deep penetration welding

激光深熔焊接热循环的研究

The Measurement of Weld Thermal Cycle in Welding by Both Sides SAW Spiral Pipe

螺旋管双面埋弧焊焊接热循环的测定

Effect of the Thermal Cycle of Welding Shrinkage Hole on Microstructure and Properties of Heat-Affected Zone Austempered Ductile Iron

焊补缩孔热循环对奥-贝球铁HAZ组织与性能的影响

The assessment model has been proved reasonable from the fact that power factorial item of CO_2 gas shielded arc welding shows good comparability with correlative item of steel-making process in electric oven, which makes it possible to quantitatively assess the whole life cycle of materials.

获得的CO2气体保护焊的能源因子项与电炉炼钢工艺过程相关项有较好的相对可比性，这也表明该评估模型是合理的，并使得材料实现全寿命周期的定量评估成为可能。

The decreasing time of free-wheeling current is relative to duty cycle in the exiting FB-ZVZCS-PWM soft-switching inverter arc welding power supply with the block capacitor, and it is hard to achieve zero current switching ( ZCS) for lagging leg with low duty cycle.

现有FB-ZVZCS-PWM软开关弧焊逆变电源采用阻断电容衰减原边环流电流所需的时间与占空比有关，占空比很小（电源输出电压很低）时滞后臂难以实现零电流开关。

Research on Determination System for Welding Thermal Cycle Curve and Phase Transformation Point

焊接热循环曲线及其相变点测试系统的研究

After welding thermal cycle, a coarse grain zone which is 0.5~ 0.7?

经过焊接热循环，焊接热影响区存在0.5~0.7mm的粗晶粒区，晶粒度只有1~3级。

In order to change the situation, based on the digesting and absorbing the inport technology, combined with the production reality, we used the welding method to make the hub. Thus obtained the result of high quality, low cost and short productive cycle.

为改变这一状况，我们在消化、吸收引进技术的基础上，结合生产实际情况，采用焊接的方法制造轮毂，取得了质量好、成本低、生产周期短的效果。

The results show that the fracture model of two pipes are the same high cycle fatigue fracture due to high original stress. Fatigue crack originated from welding line at inboard or outboard of U-pipes.

结果表明，两根导管的断裂性质相同，均为起始应力较大的高周疲劳断裂，疲劳裂纹起始于U形导管内侧或外侧的焊缝部位。

The current cycle control of AC short circuit transition welding method and system

本周期交流短路过渡焊接方法及系统钨板惰性气体保护焊

The rule of the arc-time and short-circuiting transfer cycle time under the high speed welding was researched by welding quality analyzer of Hannover.

采用汉诺威焊接质量分析仪，研究了在高速焊接的情况下，燃弧时间与短路过渡周期的变化规律。