welding test的例句大全

Orthogonal experiment design method is used to determine the optimum laser double-side welding parameters. The tensile strength of the retro-welding samples is used as the indicators of evaluating laser welding performance. The tensile and bending fatigue test are used to study the mechanical properties of welded joint.

选用正交试验设计方法确定Fe-Mn-Si形状记忆合金激光双面焊接的最佳工艺参数，以焊接后试样的抗拉强度作为评定焊接性能的指标。

Various sampling methods for joint quality test of hot-rolled steel bar are introduced and discussed from flash butt welding, arc welding, electroslag welding and other aspects. According to different joints various sampling and test results evaluation methods are introduced in detail.

介绍了热轧钢筋接头采取的多种方法，从钢筋闪光对接焊接头、钢筋电弧焊接头、电渣压力焊接头等方面进行了阐述，对各种钢筋接头检验取样方法及试验结果评定做了详细的说明。

In addition, the technological test for all position welding both low carbon steel and stainless steel pipes was carried out, and both the included angle of the joint and the welding parameters for better appearance of weld were optimally chosen as well.

并对低碳钢和不锈钢两种管材的全位置焊接进行了工艺试验研究，优选出了焊缝成形较好的接头坡口角度及焊接规范参数。

This paper discusses the material effect on the safty of LPG cylinder based on the test and determination for a welding steel LPG cylinder.

本文通过对一只钢质焊接液氯钢瓶材料缺陷的检测、试验，探讨了其对安全性能的影响。

The special requirement and superior performance against corrosion of 2RE69/ Zr702 clad tube was summarized comprehensively. Otherwise, the type of joint, welding process between tube and tube-sheet, fabrication, assembly, test& inspection of distributor was expounded briefly in this paper.

介绍了2RE69/Zr702双金属管的特殊结构、优良耐蚀性能，与管板的连接接头型式及焊接工艺、管头及液体分布器加工、装配和试验。

Through water pressure test, ammonia leakage test and field high temperature melted salt cycle test, it is shown that the tube joint welding quality meets completely the design and process demands.

经水压试验、氨渗漏检验及现场高温热熔盐循环试验，焊接接头质量完全达到设计及工艺要求。

This paper expatiates on the sampling test method of NDT on welds, discussing the sampling positions and ratio through welding procedures and welding condition analysis, which is of referential value to testers and QC personnel.

为此，对焊缝无损探伤抽查法作了较为详细的说明和分析，特别是从焊接工艺、施焊条件分析方面对抽查部位、抽查比例进行探讨，对检查人员和质量管理人员来说都具有参考价值。

Through the welding crack test of inclined Y groove, physical inspection of mechanical property of welded joint, etc, the steel plate quality and welding process were reviewed as well.

通过斜Y坡口焊接裂纹试验、实物焊接接头的力学性能检验等方法，评价了钢板的质量和焊接工艺。

Study on electrode life test for spot welding hot dip galvanized steel by method of surface titanizing

表面渗钛的镀锌钢板点焊电极寿命试验研究

Analysis of the Impact Toughness Test and Fracture of Rail Thermit Welding Joints at Low Temperature

低温下铁路钢轨铝热焊缝接头冲击韧性试验与断口分析

Measurement of Welding Residual Stress and Proof Test Stress in Hydrocracker

加氢裂化反应器的焊接残余应力和水压试验应力测试

Austenitic stainless steel welding metal-196 ℃ cryogenic impact toughness technological test

奥氏体不锈钢焊缝金属-196℃低温冲击韧性工艺性试验

Hand welding of test coupons for examination of power station welders

电站焊工考核试件的手工焊接技术

The test showed that the magnetic field added to MIG welding process for aluminum alloy could be controlled by regulating parameters of the device, intermittent time and output current to achieve good welds.

试验表明，该装置的参数调节范围大，操作方便。通过调节装置的频率、间歇时间和输出电流来控制铝合金MIG焊过程施加的磁场参数，有效地改善了铝合金的焊缝形貌。

Application of metallographic testing technique in quartz unit vacuum cold pressure welding technological test

金相检验在石英器件冷压焊工艺试验中的应用

The model of slit type cracking test for finite element analysis is established by HYPERMESH, the composite function of welding heating source and induction heating source is defined by FORTRAN program.

在有限元分析过程中，以斜Y坡口冷裂纹拘束试验为分析对象，利用HYPERMESH建立了有限元分析模型，采用FORTRAN语言编程实现了电弧热源和感应加热热源的复合作用。

Research on the test system of inverter resistance spot welding dynamic parameters

逆变电阻点焊动态参数测试系统的研究

The authors studied the welding technology and parameters for the tin-plate can and thier influence on welding speed and quality, investigated the microstructure and properties of the weld, analysed the distribution of tin in weld metal and carried out the flange test of the can body.

本文研究了罐身马口铁激光焊接工艺和焊接参数对焊接速度和质量的影响，检验了焊接接头的组织和性能，分析了Sn在焊缝中的分布，并进行了空罐的翻边试验。

At the same time the check and test data of sample welding and simulating practical stop up welding sample are given.

同时给出了试样焊接、模拟实样堵焊试样的检测试验数据。

Constant load tensile test was adopted to study the influence of welding material match and alloy element content on SSCC ( sulfide stress corrosion cracking) of domestic pipeline steels.

采用恒载荷拉伸法，测试了国产管线钢母材及其焊接接头的硫化物应力腐蚀开裂SSCC性能。结果表明：焊接匹配、合金元素是影响国产管线钢SSCC的重要因素。