welding tip的例句大全

Fine thermocouple with tip diameter less than 0.02 mm was fabricated from commonly available couple wires ( diameter 0.1 mm) under the monitoring of a microscope and by way of electrochemical erosion and spark welding.

尝试在显微监视条件下通过电解腐蚀方法，用直径100μm的普通热电偶丝制作尖端直径小至10-20μm的微细偶丝，经电火花焊接形成微细热电偶。

By means of adopting preheating before welding, low hydrogen welding and heat treatment after welding and some other steps, the built-up welding repairing of the crackle in 650 mm roller tip end was successfully achieved.

通过采取焊前预热、低氢焊接和焊后热处理等措施，成功地实现了650轧辊端头断裂的堆焊修复，即以焊代换。

Welding of Rivets on the Tip of Blade for Turbine

汽轮机叶片端部铆钉的焊接修复

The Study of Deposition of TiC on the Electrode Tip Surface of Resistance Spot Welding by Vibrating Electric Sparking

点焊电极表面振动电火花熔敷TiC的研究

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM, EDX and XRD.

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

The results show that during welding process the contact radius increases gradually, the highest temperature is always located at the center of the electrode tip surface, while the electrode stress and current density both concentrate at the edge of contact region.

结果表明：所考察的焊接条件下，接触半径在焊接过程中逐渐增大，电极端面的中部温度最高，而电极压力和电流密度均在接触区边缘集中。

The results show that electrode degradation mechanism was basically caused by wear due to fracture of local welding between the electrode tip surface and zinc coated sheet steel happen at electrode surface and alloying between electrode and zinc on zinc coated steel during resistance spot welding zinc coated steel.

结果表明：点焊镀锌钢板时电极的失效机制主要是电极和镀锌板之间局部焊接的断裂发生在电极表面而导致的电极磨损以及电极和镀锌板表面的锌之间的合金化。

Welding parameters such as angle of bending tip, pulse voltage, wire feed rate, pulse mode, size of groove and welding speed can affect the appearance of weld.

导电嘴弯曲角度、送丝速度、峰值电压、协同模式、焊接速度和坡口尺寸均会对窄间隙焊缝成形产生重要影响。

effect of tic coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel

点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的分析

industry: air purifier; humidity regulator; ion fan; tip; other welding materials and accessories;

所属行业：空气净化器；湿度调节器；离子风机；烙铁头；其他焊接材料与附件；；

evaluation of welding procedure specification with crack tip opening displacement in steel box beam

钢箱梁焊接接头的断裂韧度评定

Considering the structure of welding tool, the kinematic equations of the welding wire tip of this robot are obtained in the first time.

考虑焊枪结构，首次建立了SK6弧焊机器人焊枪末端的运动学方程。

The result showed that it is in the period of droplet growth at the tip of welding wire that an electrochemically gained oxygen was produced in the case of direct current negative polarity whereas an electrochemically lost oxygen in positive polarity.

结果表明，在焊丝末端熔滴生长阶段，直流反极性条件下存在电化学增氧，而直流正极性条件下则存在电化学脱氧。

The repairing welding process of the main wearing tip truck has been described in this article.

介绍了矿山自卸重型卡车主要磨损件的焊接修复过程.

Spare parts for CO 2 Welding Torch: Contact tip , Nozzle, Tip holder and others.

CO2气体保护焊接配件: 各种导电咀、保护咀 、 连接杆及各种焊枪配件等.