wheel tooth的例句大全

the experimental research of the temperature in the vicinity of worm wheel tooth surface

邻近蜗轮齿面处温度的实验研究

The Analysis on the Reasons for Driving Chain Wheel Tooth Fracture of Riser at Gathering Coil Station

集卷站升降机构传动链轮轮齿断裂原因浅析

Analysis on strength of the wheel tooth of cylindrical worm pair with circle-arc tooth

圆弧齿圆柱蜗杆副轮齿强度分析

the distribution feature and the fluctuation tendency of the temperature in the vicinity of the worm wheel tooth surface were investigated and analyzed.

分析了邻近蜗轮齿面的温度分布特征及温度变化的趋势。

Affection of the processing method of mine anchor chain wheel tooth pattern on using performance

矿用锚链轮齿形加工方法对其使用性能的影响

Each tooth of the ratchet wheel shears the same length and its end is heaved along wheel circumference direction.

这种棘轮的每个齿都一样长，并且每个齿的末端都沿着轮周方向凸起。

In this paper, the factors chosen were diameter and width of the wheel, vertical load on the wheel and the length of the anti-sliding tooth, then the regression equation was obtained to study the effects of all factors on sliding of the ground wheel.

选择地轮直径、地轮宽度、地轮的垂直载荷、防滑齿长度为试验因素，建立了滑移率的回归方程，研究各因素对地轮滑移率的影响。

It is put forward that experience formula to determine hardness relation between big wheel and little wheel of gear pair hardened tooth flank.

据此提出确定硬齿面齿轮副的大小齿轮之间硬度关系的经验公式。

Simplified design method for the tooth shape of the driving wheel of excavating machine

挖掘机驱动轮齿形的简化设计方法

Analysis and Research of Non-chain Drawing Mechanism with Single Circular-arc Tooth Profile Driving Wheel

单圆弧齿廓链轨式无链牵引机构的分析研究

tooth profile calculation and automatic drawing of cylindrical worm wheel

圆柱蜗轮齿形齿厚计算及齿廓自动生成

about measurement of tooth's thickness for worm wheel by involute worm ( z1) transmission

渐开线蜗杆（Z1）传动的蜗轮齿厚的测量

A Study on the New Tooth Form of the Sprocket Wheel

链轮新齿形的研究&大圆弧渐开线齿形

The Color Wheel The helical plate tooth threshing cylinder, the top thresh fan and the undershot fan are connected and driven by a vertical shaft.

该机以一根立轴联接螺旋板齿脱粒滚筒、上排杂风扇和下轴流风扇，并驱动其旋转。

The Design and Application of the Special Packing in According with the Tooth-like of the Driving Chain Wheel

驱动链轮齿形专用工装的设计与应用

The Pulse Electronics Brush Plates the Repair Rolling Mill Tooth Wheel Axle to Brush Plates the Craft Practice

脉冲电刷镀修复轧机齿轮轴刷镀工艺实践

When designing gear hob, worm gear hob and shaping milling cutter, it should be verified whether the interfere would occur between grinding wheel and the next gear tooth on condition of pledging the relief grinding length of the back of tooth.

在设计齿轮滚刀、蜗轮滚刀和成形铣刀时，要校验在保证齿背铲磨长度的情况下，所用砂轮是否和下一个齿发生干涉。

Synchrobelt transmission is kind of switching transmission of belf tooth and wheel gullet, which possesses the merit of gear, chain and belt wheel transmission.

同步带传动是其带齿与轮齿槽的齿齿啮合传动，具有齿轮传动，链传动和带传动的优点。

By improving the wheel gear grinder of large plane grinding, the tooth modification method was presented for manufacturing noninvolute beveloid gears.

通过采用特殊改形后的大平面砂轮磨齿机对渐开线变厚齿轮进行轮齿修形来获得所需要的非渐开线变厚齿轮。

According to the tooth thickness taper of evolute internal spline taper spindle in tooth, calculate the tailstock block-up thickness of the gear grinding machine, determine the grinding wheel angle of the gear grinding machine, and process the evolute taper spindle.

根据渐开线花键锥度芯轴在齿向的齿厚锥度计算磨齿机尾架垫高厚度，确定磨齿机砂轮角度，加工出渐开线锥度芯轴。