work cylinder的例句大全

The technical parameters, structural characteristics, operating principle, and application of single-action sleeve telescopic cylinder are introduced. The advantages and disadvantages of this type of cylinder in practical work are pointed out as well.

介绍了后法兰单作用套筒伸缩气缸的技术参数、结构特点、工作原理及应用范围，并指出其工作的优缺点。

Based on terminal conditions of numeric analysis, numeric analysis of the relative expanding difference of shaft and cylinder of steam turbine was made at the different temperatures in the no-load work condition by ANSYS.

利用数值分析的边界条件，运用ANSYS有限元分析软件，对汽轮机转子及汽缸空负荷工况下，不同排气温度时的相对胀差进行了数值模拟。

The work principle and the motion order of the pneumatic loop of total drill was explained based on the example of thrust force air cylinder.

本文给出了该机的原理和整体结构，介绍了钻孔模块部分。并以推力气缸为例，详细说明了整机气动回路的工作原理及其动作顺序。

The machine work of the slotting tool of the isometric profile cylinder and it's errors analysis

等距型面插刀的加工及其误差分析

He cut short his work, put down the cylinder in his hand.

他突然停止了工作，放下了手里的圆筒。

The lifting oil cylinder can not work normally due to the wear of support guide ring or gluing off release at the connecting position between the support guide ring and the inside wall of cylinder after the lifting oil cylinder used for a period of time.

在举升油缸使用一定时间后，其支承导向圈磨损或支承导向圈与缸简内壁的联接处出现脱胶剥离，致使举升油缸不能正常工作。

the experimental work was carried out on a motored single cylinder test engine, using high speed simultaneous photography technique.

试验在倒拖的单缸试验机上进行，采用了同步高速摄影技术。

through analyzing the mutual position of the department through emery wheel, guide idler, supporting board of work piece, set up the mathematical model of leading the outline shape, get the surface characteristic of the outline shape while cylinder rubbing without core.

通过砂轮、导轮、工件支板坐标系相互位置的分析，建立导轮廓形的数学模型，得到圆柱零件无心磨削时导轮廓形的表面特征。

After the intake model and the cylinder work process model of air powered engine were built, the maximal specific work output of compressed air was taken as object function, and an optimal piston trajectory was obtained.

通过建立气动发动机的进气模型和缸内工作过程模型，以压缩空气的比输出功最大为目标函数，给出优化的活塞运动轨迹曲线。

Adopt the spinning formation process, for the inner cylinder and outer jacket of stainless steel vacuum thermos, can saved raw materials, eliminated work steps and the investment of models.

真空不锈钢保温容器的内胆身及外壳采用旋压工艺成形，可节省原材料，减少加工工序及模具投资。

Safety glasses, safety shoes, and ordinary work gloves are recommended for cylinder handling.

操作钢瓶时，推荐使用安全眼镜、安全鞋和普通工作手套。

The adopting of compositive CAD/ CAM system relates itself to the quality of the whole machine. Designing work of cylinder with high efficiency and rationality is a good method that increases the performance of hydraulic transmission system and then improves the performance of the whole machine.

运用集成CAD辅助设计系统技术将直接关系到整个机体的优劣，高效合理地完成液压缸的设计工作，是提高液压系统性能进而改善整机性能的有效方法。

study to the budget methods of truncated cuspate cylinder in earth work

土石方工程中平截尖柱体计算方法的探讨

simulation work is carried out on a single cylinder diesel engine. the in-cylinder gas fluid, spray and combustion procedure are predicted.

本文对一台单缸柴油机，包括气相流动过程、喷雾过程和燃烧过程在内的缸内过程进行了模拟计算。

this paper suggests a new method to adjust the all clearance of the engine valves in two times, by checking the upper dead line of the first cylinder, which are carried on by making use of the work circulating diagram of the engine.

经过实验，提出了利用工作循环图解决用两次调整法对气门间隙检查调整时找到第一缸的压缩上止点后判断可调气门问题的新方法。

the properties of locomotive engine cylinder surfaces hardened by yag laser are studied. the hardening size calculated is in accord with that obtained from test. thus the test work volume for determining the technical parameters can be reduced efficiently.

在由YAG激光强化机车气缸套表面的试验研究中，理论计算的硬化带尺寸与试验结果一致，采用此方法确定工艺参数，可有效减少试验工作量。

Discussion about the Friction Force does Work When the Cylinder does Pure Roll along an Oblique Plane

圆柱沿斜面作纯滚动时摩擦力作功的讨论