working condition的例句大全

Additionally, some sub circuits like thermal protection, current limitation and SOA ( safe operation area) protection are included in the regulator, which makes the circuit along longevity under safer working condition.

另外，在电路中还设计了热保护、电流限制和安全区保护电路，使电路可以在更安全的状态下工作，延长了芯片寿命。

The test results show that the antifriction film bearing oil# 100 meets the necessity of using in high speed thread milling machine and under the serious working condition.

试验表明兰炼100号抗磨型油膜轴承油完全可以满足高速线材轧机精轧机组特殊工况的使用要求。

The upper set performs the mid-controller address setting, the mid-controller working condition inquiring and the threshold value of environment element setting and then achieves uniform management of several grain depots.

上位机可以设定中间控制机地址、查询中间控制机的工作状态、设定温湿度的报警阀值，从而实现对多个粮库的统一管理。

According to the practical working condition and operating record, a series of normal mechanics and fatigue damage tests are carried out with the reactor materials ( 30CrNiMo8), the test materials are obtained from the practical field.

由反应器工作的现场提取试样，依据反应器实际运行条件（温度、压力等）和服役史（运行记录），进行了一系列反应器材料30CrNiMo8钢的常规力学试验和疲劳损伤试验。

The strength and equivalent stress of the remainder wall thickness of reactor shell under new working condition were checked.

对反应器壳体剩余壁厚在新工况条件下的强度和当量应力进行了校核；

Wireless remote control technology and computer intelligent control can automatically limit the amplitude, dangerous working condition automatic alarm device, more safely and reliable.

无线遥控技术，电脑智能控制，自动限制幅度，危险工况自动报警装置；

The working condition must be altered to meet the new requirements.

工作环境必须改善，以适应新的要求。

When the hopper is put into use, users can independently select the shape of the spile according to the shape of a container or a working objective; a convenient working condition is provided;

使用时，使用者根据容器形状或工作目的自主选择插管的形状，提供便利的工作条件；

To avoid the dangerous working conditions, improve reliability and operational safety of the all-terrain crane, the main arm telescopic with the tower arm condition uses manual control at construction site.

为了减少危险工况带来的事故，提高全地面起重机的可靠性和作业安全性，一般施工现场对于塔臂工况下的主臂伸缩采用手动控制。

A: Are they satisfied with the working conditions?

10.Working conditions工作条件A：他们对工作条件满意吗？

This paper discusses the working condition of machine tool's spindle bearing can be distinguished by bearing's vibration signal.

论文阐述了利用轴承振动信号可判断机床主轴轴承的工作状态，通过频谱分析可对轴承进行故障诊断及预紧力确定；

Based on the analysis to the failure of the CC roll, a composite CC roll with the spiral water cooling form and the prestressed structure was developed by a new material suitable to the CC working condition.

在分析连铸辊破坏原因的基础上，提出了适用于连铸辊工作条件的新材质，试制出了带有预应力结构和螺旋水冷结构的复合连铸辊。

After checking and analyzing the pressurized air system working condition in aluminium smelter, we think that the major part of system leakage is the crust breaking and aluminium feeding equipment of electrolytical pots.

根据对铝厂压缩空气系统工况的检测分析认为，系统泄漏的主要部位是电解槽打壳下料气缸。

Slide valve is the key equipment in catalytic cracking unit. The working condition is very severe.

滑阀是催化裂化装置的关键设备，其工作条件十分苛刻。

The feedback control quantity has imposed on the vehicle center of mass by the form of torque, and this lead to the controller worse control effect on the side slip angle in the limit working condition.

反馈控制量以力矩的形式直接施加于整车质心，导致控制器对质心侧偏角的控制效果在极限工况时较差。

Integrated Evaluation on Thermal Working Condition in Tank Power Cabin Based on the Thermal Charge Value Method

基于熵值法的坦克动力舱热工况的综合评价

the actual working condition of night visions is analyzed from aspects of spectrum, illuminance low-light-level ( lll) source with continuously adjusted illuminance is designed, and the simulation of lll condition in lab is realized by using electrical source of steady current.

从光谱和光度两个方面分析了微光夜视系统的实际工作环境，设计了照度连续可调的微光光源，利用稳流电源供电，实现了实验室条件下的夜天光模拟。

Forklifts should be inspected and maintained in good, safe, working condition.

贯彻对叉车的日常检验和维修，以维持其良好、安全和有效状态。

In this paper, we demonstrate the thermal crack formation and its working condition.

本文论述了热裂纹的形成与工作条件。

Used software Pro/ E to establish the installments full-scale mock-up, has simulated the leaf blade through MECH/ Pro specific interface program loading ADAMS the working condition.

本文采用三维软件Pro/E建立了装置的实体模型，通过MECH/Pro专用接口程序调入了ADAMS动力学分析软件来模拟叶片的工作情况。