working temperature的例句大全

Several methods charactering upper limit working temperature of resin matrix composites are discussed.

本文讨论了表征树脂基复合材料上限工作温度的几种方法。

run until the normal working temperature is reached.

运转到温度达到正常的工作温度。

In this thesis an entire mathematical model for working temperature of torpedo thermal power system in steady state is built up.

文章建立了稳态条件下鱼雷热动力系统工作温度整体计算模型，通过算例验证了模型的正确性。

Upper limit working temperature of resin matrix composite

树脂基复合材料的上限工作温度

The working temperature was 45-50 oC, polishing duration was 15-18 minutes.

其工作温度45～50℃、抛光时间15～18min。

outer conductor: soft copper wire or tinned copper wire braid shield working temperature

外导体：软铜线或镀锡软铜线编织屏蔽

Its biggest advantage is its high working temperature& 300 degree centigrade.

具有较高的磁能积、极低的温度系数，其使用温度可高达300度。

Their working temperature exceeds the rated temperature limit or their thermal defect is one of causes which made electronic equipments disabled, this badly restricts the increase in their reliability.

嵌入式系统的过热或热缺陷是嵌入式系统失效的主要原因之一，严重地限制了电子产品的可靠性的提高。

The working temperature has a decisive effect on the various polarization losses, especially for the anode activation polarization, which indicates that the anode surface reaction rate is a key factor.

电池工作温度对各种极化损失尤其是阳极活化极化产生重要影响。

The working temperature of semiconductor lie in dissipation power, environment temperature and condition of elimination of heat, the temperature and heat stress affect greatly the Reliability and electrical performance of apparatus.

半导体器件的工作温度是由器件的耗散功率、环境温度及散热条件决定的，温度与热应力对器件电性能及可靠性有极大的影响。

The new liquid crystals feature wide working temperature range, low voltage operation and high reliability.

新型液晶的特点是：工作温度范围宽，工作电压低，可靠性高。

hard anodizing process for aluminium with high tolerance to working temperature

宽温度铝硬质阳极氧化工艺的研究

Measurement of Working Temperature Variation in Automobile Clutch Pressure Plate Surface

离合器压盘表面工作温度变化规律的测定

an n-octane/ stainless steel heat pipe blackbody has been developed with maximum cavity diameter of 60 mm arid working temperature range from 50 ℃ to 200 ℃.

研制了正辛烷/不锈钢热管式黑体辐射源。该源最大口径φ60mm，工作温度为（50～200）℃。

The instrument can not only perform the functions of PCM 3506, also can monitor the working temperature and pressure on logging casing collar.

该脉码传输仪既能完成PCM3506的全部功能，又能监测仪器工作环境的温度及测井套管接箍的压力。

We primarily do theses works: First, for the RTCVD equipment that we required has a big chamber, high working temperature and fast temperature ramp rate, the energy that required for the high temperature working conditions was computed;

针对本课题要求的RTCVD设备的反应腔大、工作温度高和升温速度快的特点，首先对设备升温条件进行能量计算；

The thermal simulation For the whole structure of the directional coupler confirm its reach in normal and high temperature heat balance working temperature will not cause damage to the device, and assure its good work.

对定向耦合器的整个结构进行了热仿真，确认其在常温及高温下达到热平衡后的工作温度不会对器件造成损害，可以保证其正常工作。

The effects of dopant and preparation method on promoting the sensitivity and selectivity, lowering working temperature, and shortening response time and recovery time are discussed.

阐述了掺杂及制备方法对提高气敏材料的灵敏度、选择性以及降低工作温度和缩短响应-恢复时间等方面的影响；

Because it has a high working temperature, the high temperature strain gauge is necessary in composing the strain measurement electric-bridge.

由于工作温度较高，所以需采用高温应变片来组成应变测量电桥。

Discussion on the working temperature and quality grade of steel material

关于钢材工作温度和质量等级的探讨