worm gear的例句大全

The design of cylindrical worm gear pair with controllable spot engagement

可控点啮合圆柱蜗杆副的设计

When designing gear hob, worm gear hob and shaping milling cutter, it should be verified whether the interfere would occur between grinding wheel and the next gear tooth on condition of pledging the relief grinding length of the back of tooth.

在设计齿轮滚刀、蜗轮滚刀和成形铣刀时，要校验在保证齿背铲磨长度的情况下，所用砂轮是否和下一个齿发生干涉。

Design and production of the worm gear in metric system transformed from that in British system and its fitting-in with the worm in British system

英制蜗轮改为公制蜗轮与原英制蜗杆配合的设计制造

Study on the High Efficient Grinding Method of Envelop Torus Worm Gear

包络环面蜗杆的高效磨削方法研究

According to physical boundary condition of extruding radial sliding bearing and Hertz elasticity contact theory, derived the distribution of pressure on the contact area between worm gear and roller teeth.

根据作挤压运动的径向滑动轴承载的物理边界条件，同时结合平面Hertz弹性接触理论，得到滚动齿与蜗轮球窝的接触域及其接触域上的载荷分布函数。

Brief Introduction of Spare Tyre Lifter of Worm Gear and Worm

蜗轮蜗杆备胎升降机构简介

Study on Motion, Force and Strength of Ball Globoid Worm Gear Drive

滚珠环面蜗杆传动的运动受力和强度分析

On Problem of Grinding Ball Globoid Worm Gear

环面滚珠蜗轮磨削问题的探讨

Basic Problems of Stand-off Cylindrical Worm Gear Design

关于变位圆柱蜗杆副设计中的几个基本问题

The upper work rolls adopt 4 worm gear adjusters. High quality and precision.

上部工作滚轮采用4点涡轮式微调装置, 适合矫直机精度要求较高的加工品质要求.

When worm gear pair is formed by standard worm and worm wheel generated by hob of type ⅱ, its sensibility to errors is reduced while the worm gear pair is assembled originally and good tooth contact quality is acquired after its running in.

本文提出失配修形法，用标准蜗杆与由Ⅱ型滚刀加工的蜗轮失配啮合，使蜗杆副初装时对误差不敏感，跑合后得到良好的接触质量。

The authors propose methods of computerized design and analysis of a spiroid worm gear drive with ground worm based on the following considerations: ( 1) The theoretical thread surface of the hob is generated by a cone surface.

作者们基于以下研究提出了精磨蜗杆的螺旋蜗杆传动的计算机设计和分析方法。1.滚刀的理论螺线表面是用一维面生成的。

Study on modification technique of hourglass worm gear tooth surface

小柱面包络环面蜗杆齿面修形方法研究

The Computer Simulation Technology of the Hourglass Worm Gear Tooth Meshing Line

环面蜗杆齿面啮合线的计算机仿真技术

Tooth surface equations of the variable tooth thickness plane worm gear transmission are deduced based on the theory of engagement.

利用啮合原理的知识，笔者推导出变齿厚平面蜗轮传动副的齿面方程。

Worm gear and worm drive, meshing gear meshing of the relative speed between sliding friction loss is big, so, the low efficiency.

蜗轮蜗杆啮合传动时，啮合轮齿间的相对滑动速度大，故摩擦损耗大、效率低。

The value of K was changed from 0.52 to 0.48, and the worm gear transmission ratio of top band increased by 22.1%. After improving, it was ensured that the sectional velocity of tobacco leaf coming out of the mouthpiece was the same.

提出了将公式中系数K由0.52改为0.48，将上排链蜗轮蜗杆传动比增大22.1%，改进后保证了烟叶从刀门输出时断面速度一致。

On circular ball curve of ball globoid worm gear drive

滚珠弧面蜗杆传动的回珠曲线

A Method for profile Calculation of Template Checking of worm Gear Hobs

砂轮轴与蜗杆轴垂直交错磨削的ZC型蜗杆传动蜗轮滚刀检验样板的廓形计算

The Experimental Research on the Scuffing Load Capacity of Worm Gear Oil

蜗轮蜗杆油胶合承载能力试验研究