yield stress的例句大全

The elastic modulus, tensile yield stress, fracture stress, and elongation of n Cu are 0.65, 1.42, 1.82 and 0.15 times of that of p Cu, respectively.

纳米铜的弹性模量、屈服强度、断裂强度和延伸率分别为多晶粗晶铜的0.65,1.42,1.82和0.15倍。

The relationship between yield stress and porosity is obtained with spherical self-consistent model. The prediction for yield stress of spherical pore Al alloy foam is in agreement with the experimental results.

采用球形自洽模型研究了球形孔泡沫铝合金的屈服应力与孔隙率关系，与实验结果吻合良好，表明该模型可以有效地预测球形孔泡沫铝合金的屈服强度。

Fractional softening evaluated from yield stress as well as relative peak stress and peak strain was measured against holding time after hot deformation.

调查了由两次加载拉伸变形时的屈服应力求得的静态软化率以及相对峰值应力比和峰值应变比随等温保持时间的变化。

Tensile modulus and yield stress of blends increase with concent ratio n of PMMA.

结果表明，共混物的拉伸模量、屈服应力随PMMA含量增加略有增大。

Factorial experiment design was carried on by dint of Design-Expert software for studying the yield stress and apparent viscosity. By variance analysis finding the remarkably influential factors, thereout the equations of the yield stress and the apparent viscosity were obtained.

借助Design-Expert试验设计软件对屈服应力和表观粘度进行正交试验，通过方差分析寻找显著影响因素，并得到了屈服应力和表观粘度的公式。

Correlation between yield stress and strain rate for metallic materials and thermal activation approach

金属材料屈服强度的应变率效应和热激活理论

The pipeline steel with strain-based design is usually characterized by high initial work hardening rate, good ductility, and low yield stress to tensile strength ratio.

抗大变形管线钢就是基于应变设计的方法得到的具有连续屈服、较低的屈强比、较高的加工硬化指数以及均匀塑性变形延伸率等特性的管线钢。

multivariate regression analysis of the yield stress of gelled crude oil

胶凝原油屈服值多元回归分析

Artificial Neural Network Model to Predict Yield Stress of Waxy Crude Oil

人工神经网络预测含蜡原油的屈服应力

The yield stress of this MR fluid is 70 kPa at a shear rate of 110 rad/ s and in a magnetic field of 600 mT.

通过自行研制的磁流变仪测得该磁流变液在磁场为600mT，剪切率为110rad/s时的剪切屈服应力达到70kPa。

The results show that the influences of the glass beads content and its diameter on the tensile yield stress and strain at yield are not significant.

结果显示，微珠含量及其直径对复合物的拉伸屈服应力和屈服发生时的应变影响不太明显。

The paper analyses the problems existed in the current approach for testing the yield stress of the magnetic-flow variation fluid, and puts forward a new kind approach for testing the yield stress, which applies the shearing deformation among the liquid to measure the yield stress.

分析了现有磁流变液屈服应力测试方法中存在的问题，提出了一种新的屈服应力测试方法，该方法利用液体之间的剪切变形测量屈服应力。

Based on the fundamental theoretics of material science, mechanics, thermodynamics and physics, the theoretical formulas for yield stress and elongation of materials have been derived in this paper that they are difficult problems in material science and metal forging technology.

本文根据材料学、力学、热力学以及物理学的基本知识，推导出了材料和压力加工等学科领域中的两个重要难题，即材资的屈服应力和延伸率的理论解析式。

The paper also approach relationship between the yield stress and blood viscoelasticity.

本文还探讨了屈服应力与粘弹特性的相互关系。

The PP/ PPga blend showed higher improvement in Youngs modulus in comparison with PP, while impact strength and tensile yield stress changed a little.

对PP/PPga（100/8）共混体系，PPga加入使杨氏模量提高，但对冲击强度和屈服强度影响不明显。

Theoretic Analyses to the Induced Yield Stress in ERF

电流变液产生屈服应力的理论分析

The cracks in the specimens with inhomogenous material generally initiate and propagate in the materials with lower yield stress.

裂纹通常在低屈服强度材料内起裂并扩展。

Because there are high yield stress, high reflect speed rate, low energy consumption, small pollution effect, etc., MR ( magnetorheological) becomes first choice for damper material.

MR材料具有屈服应力大、响应速度快、能耗低、显著的流变效应、对污染不敏感等特点，逐渐成为了新型阻尼器的首选材料。

The relationships of thickness ratio with yield stress and tensile stress of the clad were established.

在传统的混合法则基础上，建立了宽度方向应力与相对厚度比和拉伸应变之间的关系。

The effect of loading rate, test temperature and pre-plastic deformation on hydrogen induced apparent yield stress reduction have been investigated.

研究了变形速度，试验温度以及预先塑性变形程度对氢致表观屈服强度下降的影响。