motor driver

Positioning system, included the stepper motor driver X axis, Y axis and Z axis guide control module, rotating test platform, used a laser device accurate positioning waiting forinspection/ calibration instrument of test points.

导轨定位系统，包括步进电机驱动X轴，Y轴，Z轴导轨控制模块，可旋转测试平台，利用激光定位仪精确定位待检定/校准仪器的测试点。

A new design of five phase step motor driver based on CPLD is introduced. The driver can implement the full step and the half step control.

介绍了一种基于CPLD实现五相步进电机的驱动器的设计方案，可实现全步、半步控制。

The printed motor driver, which uses technology of intelligent PID is given, Ntimes PWMand intelligent power module_IPM.

给出由智能功率模块IPM构成的印制绕组电动机（简称印制电机）双极N倍频PWM可逆调速系统，它采用智能PID进行闭环控制。

Printed motor driver for intelligent PID

印制电机的智能PID调速控制

Motor driver board is connected directly with the two motors, including DC servo motor driver circuit, DC step motor driver circuit and over-current protection circuit.

电机驱动板是系统直接连接两台被控电机的执行部分，主要包括直流伺服电机驱动电路、步进电机驱动电路和过流保护电路。

Research of the stepping motor driver with switch constancy current source

脉冲电流源型步进电机驱动器的研究

Stepper motor driver circuit using mainly driven ULN 2803 chip.

驱动步进电机电路主要利用ULN2803作为驱动芯片.

The Development of a Kind of Hybrid Stepper Motor Driver

一种小功率混合式步进电机驱动器的开发

In addition, a stepper motor driver was designed for drive chip carrier, which could enhance the load capacity of the pulse generated by NI motion control card.

此外，本文设计了一套与NI运动控制卡协同工作的步进电机驱动器，增强运动控制卡脉冲信号的带负载能力，驱动芯片台工作。

Development of Blending Step Motor Driver Based on L297/ 298 Chip

基于L297/298芯片混合式步进电机驱动器的研制

Based on the three-dimensional servo tracking system of carrier-based satellite antenna, the azimuth angle, elevation angle, and polarization angle of antenna were controlled through two-dimensional motor driver mechanism.

基于舰载卫星天线三维伺服跟踪系统，通过二维电机驱动机制控制天线方位角、俯仰角和极化角。

A closed-loop control system is formed involving the DSP processor, step motor driver, step motor and electronic compass.

由DSP处理器、步进电机驱动器、步进电机、电子罗盘形成一个闭环控制系统。

The system hardware includes main control board, display and button board, and motor driver board.

系统的硬件电路板主要包括主控制板、显示按键板、电机驱动板。

A method of stepping motor driver circuit was given, composed by a chopper type current mode switch regulator and a monolithic stepping motor driver TA8435H.

提出采用斩波式电流型开关电源结合单片式步进电机驱动器TA8435H，构成一种电机驱动电路的方案。

Novel Three-phases Hybrid Stepper Motor Driver

新型三相混合式步进电机驱动器

The Design of Quarter-phase Stepper Motor Driver Based on Dual Bridge Driving Circuit

基于双极性桥式电路的两相制步进电机驱动器设计

The design focuses ona high-performance step motor driver and its control system.

本设计重点研究了高性能步进电机驱动器及其控制系统。

A new type of stepping motor driver has been designed in the paper which is used to drive three-phase reaction stepping motor.

该文设计了一种新型的步进电机驱动器。该驱动器用于驱动三相反应式步进电机。

This process is a breakdown of stepper motor driver chip drives A 3972.

这段程序是步进电机的细分驱动程序,驱动芯片是A3972.

We research on the control system of surgical robot according to control requirements. Console circuit board, motor driver module and some relative modules are designed.

结合国家863计划资助项目腹腔微创手术机器人系统研究，本文对腹腔微创手术机器人的控制系统进行研究和构建，根据机器人各部分的控制要求，设计控制电路板，搭建电机驱动控制模块等。

The computer is in control of the stepper motor driver to output impulse signals that are used to drive the stepper motor.

计算机控制步进电机驱动器输出脉冲信号驱动步进电机转动，从而实现AFM的探针一样品自动逼近，提高了操作的简便性和系统的自动化程度。

A new type of stepping motor driver which is used to drive three-phase reaction stepping motor is designed in the paper. The driver adopts subdivision control when running at low speed so that the low-frequency vibration of the motor becomes low.

设计了一种新型的步进电动机驱动器，该驱动器用于驱动三相反应式步进电动机，低速运转时采用细分控制，低频振荡小；

A method of designing stepping motor driver is given in this paper.

介绍步进电机驱动器的一种设计方法。

Low-power multi-channel motor driver IC is currently mainly used in digital cameras.

低功率的多路马达驱动芯片目前主要应用于数码相机中。

The nonlinear equations of motor driver are linearized using αβ reference frame.

采用αβ坐标系，对电机非线性方程进行线性化；

Chapter five include the content of the software flow chart of with-sensor vector-controlled induction motor driver system, the characteristic of data processing, and a novel debug method with modularization and incremental system build method.

第五章给出了带速度传感器矢量控制系统软件实现的流程图、数据处理的特点和一种新颖的模块化的编程思路和分级递增的调试方法。

This paper introduced the design of one stepper motor driver using dedicated chip L6506.

介绍了一种采用专用芯片L6506的步进电机驱动器设计。

Design of the stepping motor driver based on integrated chip

基于集成芯片的步进电机驱动器设计

Design of 2-phase Hybrid Stepping Motor Driver

二相混合式步进电机驱动器的优化设计

This paper introduces a kind of stepper motor driver with the key of MCU C8051F020.

介绍一种利用C8051F020单片机为控制核心的步进电机驱动器。