peel strength

This paper reports the hot laminating property of Maleic Anhydride grafted polyethylene ( MAH-g-PE) with aluminium ( Al) foil. Experiments shoal. that the peel strength of the resulting laminated film depends largely on processing temperature and grafting degree of MAH.

本文报道了马来酸酐接枝聚乙烯（MAH－g－PE）与铝箔的热粘接性能，并实验确定了热复合所需的温度、压力、时间条件以及接枝率的影响。

Analysis and Solvent of CCL's Peel Strength

覆铜板剥高强度问题的分析及解决

The viscosity of composite VAE emulsion was proper when the mass percentage of tackifying resin was between 6% and 9%. The composite VAE emulsion has high peel strength when amount of tackifying resin 1# was 7.5%.

实验发现，增黏树脂的用量为6%～9%时，对VAE复合乳液具有较好的增黏效果，1增黏树脂的用量为75%时，胶液具有较高的剥离强度。

However, the peel strength does not change when jet-to-substrate distance is 1 mm or 6 mm. These results correspond to the SEM results.

但是当喷头与试样的距离为1mm或6mm时，剥离强度基本没有变化，这与SEM结果一致。

High Copper Peel Strength and Excellent Alkaline Resistance.

优良的铜箔结合力和优秀的耐碱洗性.

Tested and measured the peel strength of PC with test block of different surface treatment.

对试块进行不同的表面处理，然后在试验台上进行PC料的剥离实验。

A comprehensive research was conducting on the relations among its solidified behavior, vitrification point, adhesive power, impact strength and peel strength.

研究了导电涂层固化行为与玻璃化温度、附着力、冲击强度和剥离强度之间的关系，确立了导电涂料的最佳固化条件。

In the case of composite materials, the Peel strength is an important quality metrics.

对于复合材料而言, 剥离强度是其重要的质量评价指标.

Study on the Factors of Node Peel Strength of Nomex Honeycomb

影响Nomex蜂窝节点强度因素的研究

The simultaneous measurement of the tensile strength, yield strength, stretching rate, elastic modulus, peel strength and power-of time, of a displacement curve.

可同时测量材料的抗拉强度、屈服强度、伸缩率、弹性模量、剥离强度及力-时间，力一位移曲线。

The adhesive is nontoxic and has excellent peel strength to SBS materials and leather.

所制胶粘剂对SBS材料和皮类材料具有良好的粘接效果.

Waterborne acrylic pressure-sensitive adhesives ( PSAs ) with low peel strength were prepared by the semi-continuous emulsion polymerization.

采用半连续乳液聚合法制备了一种 丙烯酸类 水基型低剥离力压敏胶.

Tests show that the FCCL is excellent at flame-retardance, soldering resistance, high peel strength, low water absorption.

通过测试表明，该FCCL阻燃性能、耐锡焊性能、剥离强度高、吸水率低。

Tightsen structural adhesives have excellent tensile, shear and peel strength maximum impact stress and vibration resistance.

泰盛结构胶具有较强的拉伸 、 剪切与剥离强度,耐冲击、耐压、抗振动.

The effect of silane coupling agents, emulsion composition and glass cloth on flexural strength of composites was studied. Furthermore, the effect of glass cloth content on peel strength of composites and effect of fluororesin content on dielectric of composites were also investigated.

实验中考察了偶联剂的种类和用量、乳液配比、玻璃布的种类对覆铜板弯曲强度的影响，玻璃布含量对剥离强度的影响，以及树脂含量对电性能的影响。

The adhesive technique with great cohesion and peel strength.

内聚强度大,剥离强度低的压敏胶粘接剂制造技术.

It can be seen that the peel strength increases when jet-to-substrate distance is 2 mm or 3 mm, and the peel strength is the largest when jet-to-substrate distance is 2 mm.

喷头与试样的距离为2mm或3mm时，剥离强度增大，当距离为2mm时剥离强度是最大的。