serial data transfer

This paper intraduces a software method for detecting the hardware protocol ( baud rate, data bits, ets ) of serial data transfer.

介绍了一种用软件侦测串口底层协议 ( 波特率 、 数据位等 ) 的方法.

The data acquisition and information processing system collects data continuously and reliably, also can work uninterruptedly for a long time. Meanwhile, it can communicate with PC by serial interface for data transfer and management.

该数据采集与信息处理系统采集数据连续可靠，能长时间不间断工作，并可通过串行接口与PC上位机通信，进行数据转存及数据管理。

Reverse Engineering of the Serial Data Transfer Protocols

串行数据传输协议的剖析研究

Based on FPGA the equipment with the functions of asynchronous serial data transfer, self-test capability, fuze product test and so on is designed and realized by VHDL program.

该设备以FPGA为核心，使用VHDL硬件描述语言设计并实现了异步串行通讯、测试设备的自检、引信产品的检测等几大功能。

To low down the cost, Terminator make use of serial port to implement data transfer.

在各个用户端，为了节约成本，采用串口传送数据的方式进行。

The system consists of signal detecting, mark checking, multiplex coding and serial data transfer.

该系统的主要部分包括激光信号的检测，打靶成绩的判断，多路信号的编码和数据的串行传送。

In high-speed fiber-optic transmission system, the serial data transfer ( up to 1Gbps) is realized by this transceiver.

在高速数据光纤传输系统中，采用该收发器实现了1Gbps的串行数据的传输。

A method of interface between microcontroller and chip with serial data transfer, and the technique of simulating serial data transfer is emphasized. Design idea of application system of single chip microcomputer based on I/ O mode is proposed.

着重介绍单片机与串行芯片及模拟串行方式的接口方法，以及基于I/O方式下单片机应用系统的设计思想。

The traditional low-speed serial, parallel data transfer has been further improved, with a more rapid rate of selection.

使传统的较低速串口、并口的数据传输做了进一步的提升，有了一个更高速的速率选择。

Development of Serial Port/ Ethernet Data Transfer Device Based on uClinux

基于uClinux的串口/以太网数据转换设备开发

In system design, LCD driver chip has some problem, this paper introduces an LVDS transmission technology to speed up serial data transfer.

对于LCD驱动芯片实际应用中的接口速度问题，本论文提出了一种用LVDS传输技术来提高串行接口传输速度的方法。

Serial Communication is a common mode of data transfer under DOS, for instance many kinds of iSBC 188 all adopt bidirectional serial port in data transfer progress.

在DOS环境下进行串行通信是数据通信的常用方式，例如各种188单板均采用双向串口进行数据传输。

In this article, the author analyzed the related technologies in the field of high-speed serial data transfer, designed a high-speed serial transmission switching system for engineering need.

本文针对高速串行数据传输领域的相关技术进行分析，然后针对工程需要设计了一套高速串行传输交换系统。

The dissertation designs a kind of data acquisition circuit based on FPGA, which mainly includes FPGA control circuit, multi-channel ADC circuit, DAC circuit and HOTLink serial data transfer interface.

论文设计了基于FPGA的多通道数据采集硬件电路，主要包括FPGA核心控制电路、多片A/D芯片组成的模数转换电路、数模转换电路以及HOTLink串行数据传输接口电路。

It also introduces the programming methods of serial port driver and data transfer aiming at the charac-teristics of uClinux, and some relative technologies of modem communication based on practical projects.

针对uClinux的特点介绍了串口驱动和数据传输的编程方法，且根据实际的项目介绍了modem通信的一些相关技术问题。