softening point

Measuring tensile test strength, film forming, softening point, and then integrated taking into account the operating conditions, and laboratory factors, film-forming agent to finalize the selection.

通过试验测定其抗张强度、成膜性、软化点，再综合考虑到实验室的操作条件等各方面因素，最终确定成膜剂的选用。

Applications of Differential Thermal Analysis on Determination Softening Point and Acid Value of Rosin

差热分析在测定松香软化点、酸值研究上的应用

This paper deals with the polymerization process of high softening point terpene resin.

本文探讨了制造高软化点萜烯树脂的聚合工艺。

The extraction separation experiment and differential scanning calorimetric measurement indicate that the resultant belongs to crystallizable isotactic polymer, possessing isotactic index ranging from 45% to 90%, melting point 215 ℃ and Vicat softening point 193 ℃.

抽提分离和差示扫描量热法测试表明，其为结晶型全同立构聚合物，全同立构含量为45%~90%，熔点为215℃，维卡软化点为193℃。

After alkylation, these resins were heated to ≤ 300 ℃ under-0.095MPa gauge pressure to remove low molecular weight substances, and terpine phenol formaldehyde resins with softening point up to ca. 160 ℃ could be obtained.

该树脂烷基化之后于－0.095MPa表压下加热至≤300℃脱除低分子物，可得软化点最高为160℃左右的萜烯酚醛树脂。

Syntheses of Terpene Maleimide Resin with Different Softening Point

不同软化点萜烯马来酰亚胺树脂的合成

The addition of MMT increases the softening point and decreases the penetration of SBS modified bitumen.

蒙脱土的加入使SBS改性 沥青的软化点升高,改善了SBS改性沥青的高温稳定性能.

Mathematically modeling of the softening point in ISP sintering Optimal control of sintering burn through point

ISP烧结块软化点数模建立的研讨铁矿石烧结终点的优化控制

The change rules of coal tar pitch's TI, QI,β-resin, softening point and coking value during the thermal polymerization modification were investigated in an autoclave.

在热聚合反应釜中，研究了煤沥青中甲苯不溶物、喹啉不溶物、β树脂、软化点及结焦值等质量指标在热聚合改质过程中的变化规律。

The tan δ peak temperature ascend as the softening point rising.

石油树脂的软化点提高,tanδ峰值温度上升.

Thy results of conventional tests ( penetration, softening point, kinematical viscosity and Fraass breaking point) and those of dynamic mechanical analysis ( DMA) on Styrene Butadiene Styrene ( SBS) polymer modified bitumen are systematically compared.

将苯乙烯-丁二烯-苯乙烯（SBS）聚合物改性沥青用常规试验方法（针入度、软化点、动粘度及脆点）与动态力学分析方法所得到的试验结果进行比较研究。

Flat tempered safety glass is kind of high-strength safety glass obtained by heating common glass to softening point and then air cooling it abruptly.

水平钢化安全玻璃是将普通玻璃加热至软化点时，然后急剧风冷所获得的一种高强度安全玻璃。

PCS material of higher softening point was beneficial to spining the fibers with greater profile degree.

熔点低的原料其异形度对压力的变化比高熔点原料更敏感，软化点高的PCS有利于纺制异形度较大的纤维。

II under-temperature calendering; resin softening point on the high side.

压光温度偏低; 树脂软化点偏高.

Engineering properties of the asphalt mastic such as penetration, penetration index, softening point, ductility, and viscosity were observed as a function of type and content of mineral filler used.

通过试验，得到了沥青胶浆针入度、针入度指数、软化点、延度及粘度等工程性质对应于不同添加剂种类及含量的函数关系。

Under the optimum conditions, the color-grade of polymerized rosin glyceride was color 5# with softening point of 152~ 155 ℃, acid value of 10~ 16 mg KOH · g~ (-1).

在优化条件下，聚合松香甘油酯色泽为加纳色号5，软化点150℃以上，酸值10~16mg KOH.g-1。

Different manufacturers, different brands of hot melt Adhesive, composition and performance, the softening point of broadband.

不同厂家 、 不同品牌的热熔胶, 组成和性能的不同, 软化点必然也有差异.

This article investigates the physical significance of softening point of Eureka pitch.

本文考察了尤里卡沥青软化点的物理意义.

High temperature microscope for glass analysis of sintering, surface tension, softening point, melting and compatibility.

高温显微镜,用于烧结, 表面张力, 软化点, 融化和兼容的玻璃分析.

Glass was heated to its softening point and reshaped in mold under its gravity in heating furnace, then was sharp quenched by cold blast immediately.

重力钢化炉的成型、钢化主要是将玻璃加热软化，玻璃在重力作用下沿成型胎边框模周边下弯成型，再将玻璃由加热炉移至急冷设备风栅间淬冷钢化。

Design on Automatic Detection Device of Asphaltum Softening Point

沥青软化点自动检测装置的设计

And the softening point, the viscosity and the solidifying point of bond decide the optimal temperature, according to the mechanism of warm compaction.

通过对温压机理的分析，发现最佳温压温度由粘结剂的软化点、粘度和固化点三个因素共同决定。