standard temperature

Measurement of antenna gain using background temperature of sky as standard of calibration

用冷空作为定标基准测天线增益

Measuring temperature is to measure the method with oviposit the most standard period.

测体温是测排卵期最准的方法.

Under laboratory conditions, after calcined at the temperature of 700 ℃, red-mud is mixed with cement to produce a special kind of concrete, with which the standard concrete is compared in terms of breaking and stress intensity.

在实验室条件下，对赤泥进行700℃的煅烧处理，并利用其制取水泥赤泥混凝土，与基准混凝土的抗折、抗压强度进行对比。

An automatic load& temperature recording device was developed to meet relevant thermo mechanical test standard.

在分析热机试验标准及熟悉试验设备的基础上，进行了热机试验设备负荷及温度自动记录装置的研制。

And radiation effect may also be included. For gas stream temperature up to 2500 ℃ ( velocity about 100m/ sec.), the new method gives satisfactory results ( errors within ± 6% as compared with standard values).

对于最高达2500℃的气流温度（速度约100米／秒），新推算方法给出了令人满意的结果（和标准值比较误差在±6%以内）。

This system is composed by a temperature chamber, several switch groups, a PC computer, a high-resolution frequency meter, a frequency standard, a control system including a simulator and a controller, a human interface based on virtual instrument.

该开发系统由温控柜、多路开关组、PC机、高分辨率频率计、频率标准、控制系统、基于虚拟仪器的人机界面组成。

Take full account of the preparation of standard test sample, set of device parameters, temperature and other details on the polyethylene pipe specimen, constant strain rate tensile, creep test and relaxation test are accomplish.

充分考虑标准试验试样制备、设备参数设置、温度调节等细节，对聚乙烯管试样进行等速率拉伸、蠕变、松弛试验，通过合理的试验处理得到真实应力应变曲线以及力学性能参数。

The friction behavior of three kinds of graphite used for nuclear reactors was tested by SRV standard high temperature friction tester under the helium and air environments The friction coefficients for the three kinds of graphite all increase with the friction speed increases.

在高温摩擦实验机SRV上对三种反应堆用石墨的摩擦系数进行了测试，实验条件分别是高温气冷堆冷却剂氦气环境和空气环境。

Design of In-situ K-type Standard Temperature Sensor Based on Two-shielded Blowing Thermocouple

基于双屏吹气偶的现场K型参考温度传感器设计

In this paper, based the standard effective temperature SET as the thermal comfort control index, a test controller of the single air-conditioning, ceiling fan and windows three coordinated control was studied to make indoor thermal environment of the SET value in a comfortable range.

本文以标准有效温度SET为热舒适控制指标，研究了一个实现单体空调、吊扇和窗户三者联动控制的实验控制器，使室内热环境的SET值处于舒适的范围之内。

This system is calibrated using a blackbody furnace as standard temperature source. The relationship between flame temperatures and grey level of the images is established through image processing and function correlation.

借助黑体炉等标定源，利用温控系统提供温度参数，经CCD系统成像得到图像的灰度值，通过函数拟合获得辐射图像灰度与温度之间的关系。