tooth thickness

Deviation of Addendum Circle and Its Influence on Thickness Measurement of Gear-tooth

齿顶圆偏差对齿厚测量的影响及修正

Thickness of the tooth body; Root canal therapy; Research.

牙体壁厚度；根管疗法；研究。

By controlling the offset distance EXF of the axis of outer cutter head to ensure the tooth thickness, avoiding the helical angle and curvature deviation generated by the existing algorithms.

通过控制外刀盘回转中心的偏距EXF保证了轮齿的齿厚，避免了现有算法产生的螺旋角偏差和曲率偏差。

To determine the tooth thickness taper of evolute internal spline taper spindle in tooth, theoretically, it is necessary to check the tooth shape locating taper spindle and the locating precision after the workpiece is mounted, as well as design the evolute taper spindle.

确定渐开线花键锥度芯轴在齿向的齿厚锥度，理论上必须验证齿形定位锥度芯轴与工件装配固定后的定位精度，设计渐开线锥度芯轴。

In the end, the superiority of plane worm with variable tooth thickness traction machine was proofed by the efficiency and load capacity test to the cylindrical wormgear and plane worm with variable tooth thickness traction.

在此基础上，通过圆柱蜗杆传动曳引机和变齿厚平面蜗轮传动曳引机的效率及承载能力试验，证明变齿厚蜗轮传动及其曳引机的优越性。

By summing up and analysis of standards for the backlash and tooth thickness deviation at home and abroad, a new method is searched to select reasonable backlash of involute spur gear and its tooth thickness deviation s.

本文是在总结分析国内外侧隙和齿厚偏差标准的基础上，以寻求一种新的选择齿轮副侧隙和齿厚偏差的方法。

This article introduces the method to calculate arc tooth thickness of bevel gear by spherical involute equate, and indicates the theory error to calculate arc tooth thickness by equivalent cylindrical gear with example.

本文介绍利用球面渐开线方程计算圆锥齿轮背锥齿形弧齿厚的方法，并通过实例指出利用当量圆柱齿轮计算弧齿厚的理论误差。

According to the tooth thickness taper of evolute internal spline taper spindle in tooth, calculate the tailstock block-up thickness of the gear grinding machine, determine the grinding wheel angle of the gear grinding machine, and process the evolute taper spindle.

根据渐开线花键锥度芯轴在齿向的齿厚锥度计算磨齿机尾架垫高厚度，确定磨齿机砂轮角度，加工出渐开线锥度芯轴。

Application of Backlash Adjustable Plane Wormgear with Variable Tooth Thickness Enveloping Worm Transmission in the Traction Machine for Lifts

侧隙可调式变齿厚平面蜗轮包络环面蜗杆传动在电梯曳引机上的应用

XE --- Rack shift coefficient adjustment of tooth thickness.

调剂齿厚的齿条位移系数.

The Over-Ball-Measurment of the Tooth Thickness of the Wormwheel of the Linear Worm Gears

线性蜗杆传动蜗轮齿厚的跨球测量

In down milling , maximum chip thickness cecum close to the point tooth contacts the work.

顺铣时, 最大切屑厚度产生于靠近刀具与工件接触点处.

Secondly, as a result of tooth thickness in the direction of tooth wear, so that active and passive gear mesh gap increased.

其次，由于轮齿在齿厚方向的磨损，使主、被动齿轮的啮合间隙增大。

By this method one can obtain a higher contact ratio under conditions of no undercut and ensure thickness of tooth top, which is possible to be manufactured by the current machine tools and the standard cutters.

这种方法可以有效地增大端面重合度，并保证所设计的齿轮不根切、齿顶不变尖，可在现有机床上使用标准系列刀具加工。

XE --- Rack shift coefficient for adjustment of tooth thickness.

调节齿厚的 齿条 位移系数.

Tooth surface equations of the variable tooth thickness plane worm gear transmission are deduced based on the theory of engagement.

利用啮合原理的知识，笔者推导出变齿厚平面蜗轮传动副的齿面方程。