凸凹

The third is in the notes on the convexconcave imprint flu.

三是在钞票上压印了凸凹感.

The rough rock walls were like the sides of a deep canal

凸凹不平的石墙就像一条很深的运河的河岸。

BW rubber expander glue bond substitutes for stepped joint or tongued and grooved joint in the horizontal joint site on the outside wall of basement.

在地下室外墙施工中，铺设BW温水膨胀橡胶止水条，取代了水平接缝处留阶梯缝或凸凹缝的作法；

The third is by mechanical means in the notes on the convex and concave imprint flu.

三是用机械在钞票上压印了凸凹感.

Debossing: The process of pressing a recess image using an un-inked block or die on paper or board. It is the opposite of embossing. With the algorithm of emboss bump mapping, the bumped text texture is implemented and can substitute for text created by modeling.

压凹：用不着墨的电版或模在纸上压成凹纹效果的方法。是浮雕压印的相反。运用浮雕凸凹纹理映射算法，实现具有凸凹感的文本纹理，可以替代真实的文本造型。

The rough rock walls were like the sides of a deep canal.

凸凹不平的石墙就像一条很深的运河的河岸。

The paper analyses the distribution regulation of air cushion field press and press grade in convex curve and concave curve of air cushion belt conveyor and discusses the curve radial R1 and the effect of belt tension on air cushion field major factors.

本文分析了气垫带式输送机在凸凹弧段运行时，气垫场的压力、压力梯度的分布规律，并讨论了凸凹弧段曲率半径R1，胶带张力对气垫场主参数的影响。

Normal and height bump maps can be combined in a material by using Addnormals function.

法线和高度的凸凹贴图可以通过Addnormals函数来合并到一种材质中.

The new kind of CSD diamond abrasive with the crumb structure which consists of many fine crystals has the character of coarsen and scraggy surfaces, it can avoid that single cystals early fall off because of the fast-ness in the bonder;

由多个细小晶粒构成的团粒结构的GSD金刚石磨料新品种，具有表面粗糙、凸凹不平的形貌特征，且在结合剂中把持牢固，避免了单晶磨料过早脱落的现象，使得磨具寿命成倍提高；

As the filling of mercury in the knaggy pore space made the pore flow channel more uniform, the fractal factor in the mercury ejection process is smaller than that of mercury injection process.

由于压汞过程中的汞对孔隙凸凹的填充，使得孔隙流通通道均匀化，因此和压汞过程相比，退汞过程的分形结构因子普遍较小，即退汞流动通道的均质性增强。

Waste from the punch and die and the base under which opened the tank discharges.

废料从凸凹模和下底座中所开的槽中排出.

The attendant smoothed away the slight irregularities in the retuning track.

随从把回来路上有点凸凹不平的地方平整好.

Farmers financing demand shows the "U" shape and the inverted "U" shape, which is"" concavo convex phenomenon.

农户融资需求的U字型和倒U型，即凸凹现象。

The springback angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases with increase of the blank holder force, sheet thickness, friction coefficient and material hardening exponent.

回弹角随凸模圆角半径和凸凹模间隙的增大而增大，随压边力、板料厚度、摩擦系数和材料硬化指数的增大而减小。

Design of Drawing and Piercing Compound Die with Floating Punch Block

带有浮动凸凹模的拉伸冲孔复合模设计

Geometry texture is constituted by anomalous small bumpiness, it lies in microcosmic geometrical form.

而几何纹理则是由不规则的细小凸凹构成的，取决于物体表面的微观几何形态。

Deviations of ovality, perpendicularity and partial concave-convex on large-scaled storage tanks are inevitably in construction.

大型储罐在施工中椭圆度 、 垂直度及局部凸凹度的偏差不可避免.

This paper introduces the developing of a cylindrical gear drive with dual convex-concave mesh& the bidirectional circular tooth gear drive.

本文开发研究了一种具有双重凸凹啮合的圆柱齿轮传动&双向圆弧齿轮传动。

It doesn't actually alter geometry but rather affects the over a surface.

它其实并不能改变模型的形状,而是通过影响模型表面的影子来达到凸凹效果的.

Faults developed and uplifts alternate with depressions are the main structure features of this area. Multi-cycle is one of the major deposit characteristics whereas composite reservoir system is the basic petroleum geologic features.

断裂发育、凸凹相间是其主要的构造特征，多“旋回”是其主要的沉积特征，“复式油气藏”发育是其主要的石油地质特征。

Push the handle gently until the concavo convex parts of both clutches occlude automatically.

用手轻推手柄待两个离合体的凸凹处重合后便会自行咬合.

The beneath strutting must level off and equilibrium if lie flat, not suitable too high. The attendant smoothed away the slight irregularities in the retuning track.

若平放，底层支撑应平整均衡，码放不宜过高。随从把回来路上有点凸凹不平的地方平整好。

Research on Ultrasonic Inspection for Cambered Surface of Die Forging Profiles

异型模锻件凸凹弧面区超声波检测方法的研究

The Measurement of the R and n of a Convex Lens On the Definition of Convex-Concave Functions

凸透镜曲率半径与折射率的测量关于凸凹函数的定义

The bench fitter's first job is to produce a cavity and core free of machine marks and to the shape and dimensions specified on the mould detail drawing.

装配钳工的首要工作是去除凸凹模的机加工痕迹，获得模具零件图上标注的形状及尺寸。