holding time

The results show that quenching temperature, tempering temperature and holding time are determining factors.

结果表明：加热温度、回火温度、保温时间起着决定性作用；

Effect of Holding Time at High Temperatures on Tensile Strength of AMC

保温时间对铝基复合材料抗拉强度的影响

Annealing: Heating to 800 ~880 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至800～880℃,在此温度停留1～3小时, 在炉中冷却.

Influenced parameters of rheological characteristic of semi-solid alloys includes temperature, strain rate and holding time.

影响合金半固态流变特性的参数为坯料加热温度、应变速率和保温时间。

Annealing: Heating to 740 ~770 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至740～770℃,在此温度停留1～3小时, 在炉中冷却.

The effect of holding time on properties of porous ceramic support sintered at low temperature

保温时间对低温烧成多孔氧化铝支撑体性能影响的研究

Annealing: Heating to 780 ~820 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至780～820℃,在此温度停留1～3小时, 在炉中冷却.

Effects of Holding Time on Intergranular Phase and Mechanical Property of GPS Silicon Nitride Ceramics

保温时间对GPS氮化硅陶瓷晶界相及力学性能的影响

Annealing: Heating to 830 ~880 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至830～880℃,在此温度停留1～3小时, 在炉中冷却.

And the holding time with fluxes is 10~ 12 min.

带渣静置，一般为10～12分钟。

Annealing: Heating to 750～780℃ , Holding time 1～3 h, Colding in furnace.

退火: 加热至750～850℃, 在此温度停留1～3小时,在炉中冷却.

Hardening Holding Time and Hardness Distribution of Hardened Layer by Plasma Surface Quenching

等离子表面淬火的淬硬保持时间与硬化层的硬度分布

Annealing: Heating to 400 ~650 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至400～650℃,在此温度停留1～3小时, 在炉中冷却.

Do devil beast world 3.13 complete versions customers need renewal after holding time be loaded with?

魔兽世界3.13完整版客户端下载之后需要更新 吗 ?

Annealing: Heating to 820 ~870 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至820～870℃,在此温度停留1～3小时, 在炉中冷却.

The results show that with the holding time prolonged the value of tensile strength increases gradually;

结果表明：随恒温保持时间的延长，σb逐渐升高；

The process of crack healing depends mainly on the normalizing temperature rather than the holding time.

愈合过程主要取决于加热温度，而愈合保温时间及愈合次数的影响相对较小。

Annealing: Heating to 800 ~850 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至800～850℃,在此温度停留1～3小时, 在炉中冷却.

Loading rate and holding time are obtained by experiments.

通过试验获得了最佳的加载速率及保压时间。

Annealing: Heating to 830 ~860 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至830～860℃,在此温度停留1～3小时, 在炉中冷却.

Effect of heating rate and holding time on microstructure of brazing joint is analyzed.

观察并分析了升温速率及保温时间对接头显微组织的影响。

The phase changes and thickness of the boronizing layer with different holding time are studied.

研究了不同时间感应加热对渗硼层层深的影响及显微组织变化。

Annealing: Heating to 710 ~740 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至710～740℃,在此温度停留1～3小时, 在炉中冷却.

Feasibility studies on shortening the holding time in austenitizing

缩短淬火保温时间可行性的研究

A method for determining minimal holding time of chemical reactor sequence by dynamic programing

动态规划确定化学反应器序列最小占用时间的方法

Suggests that the holding time in austenitizing should be shorten by one third.

建议将现行淬火保温时间缩短1/3。

The trends of influence of holding time on joint organization performance keep consistent with no pressure.

钎焊保温时间对接头组织性能的影响趋势与未加压时一致。

Annealing: Heating to 780 ~850 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至780～850℃,在此温度停留1～3小时, 在炉中冷却.

The influences of foaming and holding time on bubble diameter devitrifiedglass have been studied.

介绍了梯温炉的结构及原理,根据测量结果绘制了发泡温度与泡径的关系曲线.

A New Frame Synchronization strategy for Digital Communication with Long Holding Time

数字通信中一种具有长保持时间的新型帧同步系统