holding time的例句大全

The results showed that the normal growth of refined grain at the pertinent thermal processing temperature range and holding time has no deteriorative effect on the refinement, i.e., the refined grain was still much finer than unmodified grain.

结果表明，热加工温度下材料内部正常晶粒长大不会使其丧失变质细化效果，晶粒仍比无变质细化的铸棒细得多。

A method for determining minimal holding time of chemical reactor sequence by dynamic programing

动态规划确定化学反应器序列最小占用时间的方法

The results show that quenching temperature, tempering temperature and holding time are determining factors.

结果表明：加热温度、回火温度、保温时间起着决定性作用；

The article briefly introduces a calculating method of vacuum heat treatment thermal hysteresis time, to accurately and reasonablely decide vacuum heat treatment heating and holding time.

简要介绍了真空热处理加热滞后时间的计算方法，为准确、合理地确定真空热处理加热保温时间提供了理论基础。

The effect on the microstructures of the brazing seam of Ag-CdO contact terminal and Cu contact bridge by different brazing technological parameters including temperature, holding time and joint gap was analyzed. Based on the analysis, the optimum technological criteria put forward.

分析了Ag-CdO触头与Cu触桥钎焊温度、保温时间、钎焊间隙对钎缝组织的影响，并提出了获得理想组织的最佳工艺规范。

Loading rate and holding time are obtained by experiments.

通过试验获得了最佳的加载速率及保压时间。

The injection molding process of thermoset plastics bulk molding composition ( BMC) made of automobile lamp reflector is presented in the paper. Process parameters are settled such as barrel temperature, screw speed, injection pressure, injection velocity and holding time and so on.

介绍了热固性团状模塑料（BMC）注射成型汽车前照灯反射镜的工艺过程，确定了BMC注射成型的料筒温度、螺杆转速、注射压力、注射速度和保压时间等工艺参数。

Variation of temperature of liquid brass as well as preheating temperature and thickness of steel strip did not change the thickness variation pattern of cladding layer, but affected the holding time at individual stages and thickness of the cladding layer.

铜液温度以及钢带预热温度和厚度变化不改变复合层厚度的变化规律，但对各阶段的持续时间和复合层的厚度有影响；

Under the combination effect of yield, creep and thermal gradient, best holding temperature and holding time exist.

在材料屈服、蠕变和温度梯度共同作用下，局部热处理存在最优的恒温温度和恒温时间。

As extension of holding time at 960 ℃, tetragonal structure transforms into orthorhombic gradually.

随着高温保持时间的延长，四方结构向正交结构转变。

The results showed that the deformation induced ferrite inverse transformed to austenite and grains growted within holding time after deformation.

结果表明，在变形后的保温过程中，形变诱导的铁素体先逆相变为奥氏体，同时伴随着诱导铁素体晶粒的长大；

By observing the microscopic shape of bonding-surface under the conditions of different temperature, holding time and deformation, the effect of these factors on the bonding process of inner void defects was studied systematically. And the law of void bonding was also obtained.

通过观察在不同温度、保温时间和变形量条件下空洞型缺陷的焊合界面微观形貌，系统地研究了温度、保温时间和变形量对空洞焊合过程的影响，得到了空洞型缺陷的焊合规律。

Fractional softening evaluated from yield stress as well as relative peak stress and peak strain was measured against holding time after hot deformation.

调查了由两次加载拉伸变形时的屈服应力求得的静态软化率以及相对峰值应力比和峰值应变比随等温保持时间的变化。

Generally we considered the affection elements of the temperature test results, is the temperature, holding time, temperature change rate and so on.

通常认为，影响温度试验效果的要素有温度、停留时间、温变率等。

By analyzing temperature field, the forming process of the hardened layer was studied. It was pointed out that hardening holding time is an important factor in the course of forming hardened layer by plasma surface quenching which belongs to short time quenching.

通过分析温度场，对等离子表面淬火相变硬化层的形成过程进行了研究，提出等离子表面淬火属于短时淬火，在硬化层的形成过程中，淬硬保持时间是重要的影响因素。

But the exemption is conditional, such as the issuer or investor qualification requirements, holding time, release methods and resale restrictions.

但豁免是有条件的，诸如对发行人或者投资者资格的要求，持有时间，发行方式以及转售限制。

The effect of heating temperature, holding time and cooling mode on its crystallizability and dissolution rate of potassium is not obvious.

改变合成温度、保温时间以及冷却方式等，对合成试样的结晶性能以及试样中钾元素溶出率的影响很小。

The influence of amount of potassium oxide addition, heating temperature, holding time and cooling mode on crystallizability of and dissolution rate of potassium from potash fertilizer were investigated.

考察了氧化钾加入量、加热温度、保温时间以及冷却方式对合成钾肥结晶性能和钾元素溶出率的影响。

But for the die-cast Mg-Al-Nd magnesium alloy, when the holding time of solution treatment was same, the ultimate tensile and elongation of alloys would increase while the yield strength of alloy could be decreased with the solution treatment temperature heighten.

对于压铸态Mg-Al-Nd镁合金，当固溶处理后保温时间相同，随着固溶温度的升高，合金的抗拉强度和伸长率升高，但是屈服强度却降低了。

The test results show that: By holding time is 6 hours at 1330 ℃, performances of synthetic cordierite by the 4# recipe are better, and the cordierite samples have low thermal expansion and content of synthetic cordierite is most.

本试验研究结果表明：采用4配方经烧成温度为1330℃，保温时间为6小时后合成堇青石的常温指标较好，而且该试样具有较低的热膨胀性、合成堇青石的含量较高。