burst-level loss system input by bursty bursty with the same peak rate is an important queueing model in the study of resources allocation and call admission control in atm networks.

new technique of selective sand control and separate zone water injection

机械分层防砂分层注水新技术的研究

the analysis of correlations indicated that strong significant negative correlations were observed between dough stickness and max resistance, r/ e, peak time, peak area and 8 min band width, but there was significant positive correlation between dough stickness and extensibility.

相关分析表明，面团粘度性状与最大拉伸阻力、拉伸比、峰值时间、峰值面积和8min带宽呈显著负相关，而与延伸度呈显著正相关。

results show that the peak request value of united revocation is lower than other three schemes and the peak bandwidth value is narrower and the risk is reduced.

结果表明，相对传统的证书撤销机制本文所提出的联合证书撤销方案能使峰值请求率降低、峰值带宽变窄、安全风险降低。

the results show that the change of the position and intensity of ir absorption are related to the preparing conditions and the grain size.

结果表明，纳米氧化铝IR谱的峰值、强度和带宽有规律变化与制备因素、颗粒尺寸及结构有关。

the influence rules of writing parameters on the peak reflectivity and reflective bandwidth were investigated by ( using) matlab.

用Matlab数值仿真方法研究了光栅初始写入参数对其峰值反射率和反射带宽的影响规律。

this paper discusses a correcting way of the rudder servo control system through frequency domain response design method and then focuses on the frequency characteristic of the position feedback, such as, phase margin, magnitude margin, syntonic peak value and close-loop bandwidth and so on.

在此基础上，通过频率域响应设计方法，进行位置反馈校正网络的设计。同时重点考察所设计系统的相角裕度、幅值裕度、谐振峰值、闭环带宽等频率特性量。

then, from the coupled wave theory, the internal structure, the diffraction efficiency, the peak wavelength, the band width, the affection of recording medium's expanding and shrinking etc. are thoroughly researched.

其次，从耦合波理论出发，对反射全息图的内部结构、衍射效率、峰值波长、带宽、记录介质胀缩的影响等方面进行全面的研究。

according to the requirements of a lithography exposure system on illumination uniformity, the illumination errors caused by peak reflectivity or bandwidth or centroid wavelength within same range of roughness are discussed.

根据光刻系统对照明均匀性的要求，讨论了在相同粗糙度变化范围内，分别由峰值反射率、带宽和中心波长引起的照明误差。

by analyzing reflective properties of multilayers, the peak reflectivity, bandwidth and centroid wavelength as a function of roughness, period thickness and thickness ratio were obtained.

通过对极紫外多层膜反射特性的分析，得到了峰值反射率、带宽和中心波长分别随粗糙度、周期厚度以及比值变化的函数关系。

according to total illumination uniformity error allowed for mask, requirements for multilayer peak reflectivity and bandwidth and centroid wavelength were proposed.

在此基础上，根据允许掩模引入的总照明误差，给出了多层膜的峰值反射率、带宽和中心波长等三个参量必须达到的要求。

three functions of peak reflectivity and bandwidth and centroid wavelength related to roughness are obtained by fitting above results.

通过拟合计算结果，得到了峰值反射率、带宽和中心波长与粗糙度的函数关系。

thus, we can regulate the parameters of the filter at the different temperature range according to different requirement, and realize dynamic regulation of the gain flattening filter.

可根据不同需要在不同的温度范围内调节滤波器的损耗峰值和带宽，实现增益平坦滤波器的动态可调。

by using peak-band algorithm, the aim area ( b area) is segmented from the wear area image.

在此基础上，使用峰值带宽法从磨损区图像中分割出目标区，并通过链码边界搜索法得到了目标区的边界描述。

it can be considered that-40 ℃ is brittle transition temperature of cement clinker, because of the changes of load-displacement curve of the whole process, peak force and grinding power consumption with temperature.

综合载荷-位移全过程曲线、峰值载荷、粉碎功耗随温度的变化情况，可以认为-40℃为水泥熟料脆性转变温度，在-40℃以下进行粉碎作业时能起到节能降耗的效果。

by low temperature mechanical testing instrument, effects of the temperature on load-displacement curve, peak force and grinding power consumption were discussed.

采用低温力学试验设备，研究了载荷-位移全过程曲线、峰值载荷、粉碎功耗随温度的变化情况。

the results show that these methods can reduce the consumption of average power and peak power simultaneously on the condition that test coverage is guaranteed, and that the integration of the several methods utilizing the advantage and remedy will make the low-consumption bist systems optimum.

分析结果表明，这些方法不但在保证测试覆盖率的条件下，降低了测试平均功耗和峰值功耗，而且综合应用这几种方法将会使系统功耗指标达到最佳。

in this technique, at a time in the scan testing ( including both scan shifting and capture cycles), only one scan chain is active. the average, peak and total test power is reduced significantly.

此技术中，在扫描测试的任意时刻（包括扫描移位周期和捕获周期），仅有一个子扫描链活跃，电路的平均功耗，总功耗和峰值功耗都显著降低。

the experiment results demonstrate that our proposed scheme and test generation method can reduce the average power, peak power and test application time effectively.

实验结果表明，此方案及基于此方案的测试生成方法能有效地降低平均功耗、峰值功耗和测试应用时间。

first a compact power model of scan based bist is proposed. based on the model, excessive peak power consumption during test can be avoided by adjusting the bist period and controlling each bists startup.

首先本文提出了基于扫描BIST的精简功耗模型，在此模型的基础上，提出了通过调整扫描周期和扫描起动时间的办法来避免过高的SoC测试峰值功耗。

the circuit characteristics are abstracted at microarchitecture level and a microarchitectural peak power estimation model is implemented.

对处理器的电路级特性进行微体系结构级抽象，建立了参数化的峰值功耗估算模型；