cladded的例句大全

the simulation of seismic explosive source residual deformation in explosion cladded material

地震爆炸震源模拟爆炸复合材料中的残余变形

study on process of laser cladded nuclear valve parts

核阀零件激光熔覆工艺合理性研究

Study of laser cladded Co-based alloy/ SiC_p coatings on IF steel

IF钢表面激光熔覆Co基合金/SiC p涂层的研究

structure of laser cladded ni-based alloy coating.

镍合金激光熔覆层的组织结构分析。

developing cladded rare earth wire feeding process to expand product variety of re treatment steel

开发结晶器喂稀土丝方法扩大稀土处理钢品种

processing and microstructure of laser cladded cu base composite coating on the surface of an al alloy

铝合金表面激光熔敷铜基复合材料涂层的工艺和组织

likelihood ratio identification method for the detection of adhesive state of the liner cladded in the rocket motors

火箭发动机包覆粘接状态检测似然比识别方法

the important reason is the nanometer effect of nano-al_2o_3/ tio_2 introduced into the laser fast cladded coating.

主要是因为激光快速镀覆工艺及引入纳米材料的纳米效应的综合作用结果。

the experimental results show that the laser cladded layer of the specimen possesses higher hardness, wear and corrosion resistance.

试验结果表明，激光熔敷层具有较高的硬度和良好的耐磨抗蚀性能。

the cross-section analytical model of the laser cladded coating by powder feeding method

送粉式激光熔覆层横截面面积的分析模型

macroscopic residual plastic deformation in explosion cladded sheets are discussed on the basis of a large amount of experimental data.

本文以大量实验数据讨论爆炸复合板的宏观残余塑性变形。

processes of hot rolling and cold rolling for explosion cladded ni-ti plate are introduced with crystalline structure and properties of the plate given.

本文叙述了镍-钛爆炸复合板热轧和冷轧的工艺、组织和性能。

in this paper, the experiment study of laser smelting wc-b_4c-sic-co alloy cladded on the 45 steel surface by using a high power co_2 laser is presented.

本文介绍了用大功率CO＿2激光束在45钢表面进行WC－B＿4C－SiC－CO激光熔覆处理。

then the scattering cross section of the spherical target and cylinder target cladded with radial non-uniform plasma varies with the change of incident wave frequency was calculated.

在此基础上，对上述径向非均匀等离子体覆层球形目标的散射截面以及圆柱形目标的散射宽度随入射波频率的变化情况进行了数值计算，并对所得结果进行了仿真验证。

in this paper, the effect of different laser cladding parameters and different rare earth contents on cracking susceptibility of aviation blade with casting defect cladded by laser was studied.

研究了不同激光熔覆工艺参数和添加不同稀土含量对航空发动机叶片铸造缺陷激光熔覆开裂敏感性的影响。

the problem of scattering of a plane electromagnetic wave incident on an impedance conducting cylinder cladded with a composite and anisotropic chiral medium sheath is solved.

本文解决了平面波入射时涂覆各向异性复合手征介质的阻抗圆柱体的电磁散射问题。

the special valve in the petroleum exploitation requires excellent corrosion resistance, so the valve wall must be cladded with the highly corrosion resistant material during the production of valve.

石油钻采专用阀门的使用有耐强腐蚀性要求，制造时需在内壁表层堆焊耐腐蚀材料。

the corrosive product is al 2o 3. after each thermal cycle, the final residual stress in laser cladded coating is as a result of the common action by thermal stress and phase transformation stress.

腐蚀产物为Al2O3。每次热循环后，熔覆层中的最终残余应力是残余热应力和相变应力共同作用的结果。

The results show that the microstructure, the dilution rate and the high temperature impact slide wear resistance of the laser cladded coating have obvious advantages over the spurt cladding processing.

结果表明：激光熔覆层的组织细密均匀，气孔、夹杂物少，稀释率低，其抗高温冲击滑动磨损性能明显高于等离子熔涂工艺。

Laser cladding of Co base alloy on the nuclear valve sealing surface are performed with a 5 kW CO 2 transverse flowing laser. The microstructure and the high temperature impact slide wear resistance of the laser cladded coating and the plasma cladded coating are studied.

应用5kW横流CO2激光器对核阀阀瓣密封面进行Co基合金的激光熔覆处理，对激光熔覆层和等离子熔涂涂层进行了显微组织分析和抗高温冲击滑动磨损性能对比试验研究。