curing temperature的例句大全

a model was built by using ansys to simulate the curing temperature field of two green tires, of which one was preheated and another was not.

采用ANSYS建立轮胎硫化温度场分析模型，对经过预热和未经预热处理两种情况下的胎坯硫化温度场进行了模拟。

according to the amount of tests, the effect law of mixing ratio of fly ash, cement water ratio, curing temperature to concrete strength of 28 days is discussed, the test mixing and the strength improving law is expressed through three dimensions mathematics model.

经过大量试验，初步探讨了粉煤灰掺量、胶水比、养护温度对混凝土28天强度的影响规律，建立的三元数学模型较好地描述了这一强度增长规律。

A study was made on concrete creep under different curing temperatures, and the comprehensive effects of time and temperature on creep development were expressed with the chemical reaction rate.

对不同养护温度下的混凝土徐变进行了研究，用化学反应速率描述温度对混凝土徐变的影响。

The key consideration and the pouring temperature of the concrete under low temperature construction, curing temperature, heat storage and holding time parameters on the maximum temperature rise inside the concrete, as well as the size of the surface tensile stress, and draw some useful conclusions.

重点考虑和阐述了混凝土在冬季施工下的浇注温度、养护温度、蓄热保温时间等参数对混凝土内部最高温升以及表面拉应力大小的影响，得出了一些有益的结论。

the influence of treating methods of the cotton fabric, curing temperature, addition of salt and bath ratio upon dyeing are also discussed.

文章还讨论了棉织物处理方式、焙烘温度、盐及染色浴比对染色的影响。

with curing time and post-curing time increased, the compression set was improved. reasonable choice of curing temperature and curing time, can make vulcanized rubber with good comprehensive performance.

合理选择硫化温度和硫化时间，可使得硫化胶具有较好的综合性能，采用二段硫化能提高硫化胶的力学性能，二段硫化时间为2h时综合性能较佳。

Come through the curing temperature by differential scanning calorimetry ( DSC), Curing trial in combination with curing reaction appropriate curing time.

通过差式扫描量热法（DSC）得出固化温度，并结合固化试验得出固化反应适宜的固化时间。

A series of trials on cement-stabilized base course mateials, such as unconfined compressive strength, dry shrinkage and temperature shrinkage, were done under the condition of curing temperature 25 ° C and 10 ° C.

在养生温度为25°C和10°C的情况下，分别对水泥稳定碎石基层材料进行无侧限抗压强度试验、干缩试验以及温缩试验。

The properties of the inorganic cementing and grouting materials for fast anchorage ( abbreviated to ICG-ⅲ) and the effect of curing temperature were studied.

研究了一种无机快速锚固灌注材料（ICG-Ⅲ）的性能及施工温度对其性能的影响。

Forming curing tank after the curing temperature of168~ 180 ℃.

成型后在硫化罐内硫化，温度为168～180℃。

In order to determine reasonable processing parameters, heating of thermosetting molding compound in the mold and that of heat transfer after curing temperature are analyzed.

本文就模压料在模具中加热过程和达到固化温度以后的传热过程进行定量分析，以确定合理的工艺控制参数。

Determination of Curing Temperature and EV Time for Thick walled Rubber Article

橡胶厚制品硫化温度与等效硫化时间的测定

the experimental results show that the interaction between filler and crosslinking density decreased with the curing temperature increased, but the cure rate and compression set increased.

研究表明：随硫化温度增大，填料间相互作用、交联密度减小，T10和T90明显缩短，压缩永久变形增大。

The experimental results show that the curing temperature of the modified MDPES for making the composite mainly depend on both the reaction of network formation and the cleavage of the ether linkages in BE.

研究表明，选择BE/MDPES的固化温度时，必须同时考虑网络的形成反应和BE中醚键的断裂反应。

Preparation of acid-resistant non-solvent epoxy adhesive with low curing temperature for lead-storage battery

低温固化铅酸蓄电池用防腐耐酸无溶剂环氧胶粘剂的研制

Determination on curing temperature curve of paints for coloured sheet

彩板涂料固化温度曲线的测定

The customer can use OPP by standard thick film printing process with curing temperature 200 ℃.

采用厚膜印刷工艺，200℃固化。

Moderate curing pressure and curing temperature were beneficial to composite properties.

适中的固化压力与固化温度有利于材料具有较好的力学性能与导电性能。

This may be done in a reciprocating screw machine where one charge at a time is brought to curing temperature.

这可能是在做往复螺杆机，其中一名主管在一个时间是带来的固化温度。

Influence of Curing Temperature on Performance of Epoxy Thermosets

固化温度对环氧树脂固化物性能的影响