Piston的例句大全

Automatic machine tool for turning double end face of the piston pin Car World

车活塞销双端面自动机床

The GT code system of internal combustion engine piston parts

内燃机活塞成组编码系统

Based on the permanent mold casting process of Al-piston, with top insulating riser feeding process, semi-permanent insulating sleeves matching permanent mold casting process of Al-piston have been designed.

根据金属型铸造铝活塞的工艺特点，采用顶部保温冒口补缩工艺，设计了能与铝活塞金属型铸造工艺相匹配的半永久型保温冒口套。

The transcritical carbon dioxide rolling piston expressor ( expander-compressor) is developed to replace the throttling valve in the CO2 transcritical cycle for the improvement of the performance efficiency of the CO2 transcritical cycle and decreasing larger throttling losses.

为提高二氧化碳跨临界循环效率，解决系统节流损失大的问题，研究开发了新型的滚动活塞转子式压缩膨胀机，来代替二氧化碳跨临界系统中的节流阀。

This paper analyses the flow characteristics of the variable axial piston pumps through flow pulsation resource, putting forward a method to reduce the reduction of pressure pulsation and the test result of a pump.

分析了变量轴向柱塞泵的流量特性，从该类泵流量脉动源出发，提出了减少泵压力脉动双幅值误差的方法.给出了该类泵减小压力脉动的数学模型及某泵的试验结果。

Through the shallow hardening treatment, the steel T8A can have better contact-fatigue resistance to the repeatedimpactload-test and can be used for making the piston of rock drill.

经薄层硬化的T8A钢，可以获得较好的多冲接触疲劳抗力，故有可能作为凿岩机活塞用材。

The steering engine is steered through the position of the cylinder on the piston rod which is controlled by hydraulic pressure.

利用油压控制油缸在活塞杆上移动的位置进行操舵。

The piston, through the connecting rod, transfers to the crankshaft the force created by the burning fuel mixture.

活塞，通过连杆，与曲轴相连并将燃烧混合气产生的力传给曲轴。

"ENGINE TORQUE When the piston is moving down on the power stroke, it is applying torque to the engine crankshaft ( through the connecting rod)."

发动机扭矩：当活塞处于做功行程而向下运动时，所产生的扭矩通过连杆传递给发动机曲轴

This paper investigates forces applied on port plate surface of point contact axial piston motor, and introduces a solution of the problem of additional tilting moment of the cylinder body caused by applied force not on supporting point.

本文通过研究点接触式轴向柱塞马达配流面的受力情况，介绍了运用静压平衡理论设计平衡油室的办法，解决缸体上存在的由于作用不在支承点上所造成的附加倾复力矩的问题。

Analysis of Lateral Thrust on Main Cylinder Rod of Hydraulic Swing Beam Shear on the Basis of Finite Element Analysis hoel of piston crown

液压摆式剪板机主油缸活塞杆侧推力有限元分析

The results of calculating and experimenting show that the first and largest slap of impact between the piston and the liner occurs around the top dead center from the nonthrust to the thrust face.

经计算和实验表明：活塞在上止点附近，当活塞由非推力面快速地移向推力面时，对缸套具有较大的冲击能量。

This paper mainly introduces some theoretic calculations and verification tests on thrust force and acting time of piston actuator.

从理论上计算了活塞作动器的输出推力和作功时间，通过试验进行了实验验证。

The paper introduces the improvement of the traditional push system, that is, the floating piston-type and differential connecting push system is adopted to decrease the thrusting force and increase the advancing speed.

对传统的推移系统进行改进，采用浮动活塞式和差动联接式的推移系统，可以降低推溜力，提高移架速度。

When tightening the fastening nut, hold at the piston rod using a7-mm open-ended wrench.

拧紧紧固螺母时，请使用7-mm开口扳手托住活塞杆。

According to the simulation calculation results of piston slapping, we can see that the radical acceleration and tilting angular acceleration of the piston near the top dead center in the combustion stroke are most, so the piston slapping is the most serious.

根据活塞敲击运动仿真计算结果发现活塞在燃烧上止点附近的径向加速度以及绕销轴的摆动加速度最大，从而导致活塞对缸套的敲击也最大。

Real-Time Measuring Device and Test Research for Friction Force of Engine Piston Pair

发动机活塞组摩擦力实时测量装置及试验研究

Influence of mould releasing time of direct quenching of ZL110 alloy chain saw piston making use of remanent heat after casting on quenching effect and strengthening of artificial aging were studied.

探讨了ZL110油锯活塞铸造余热淬火的脱模时间对铸淬效果及人工时效强化规律的影响。

The development of the complex measurer for the measurement of the fuel supply pressure of VE type fuel injection pump and the piston track of timing advance device

VE型喷油泵输油压力和提前器活塞行程综合测量仪的研制

Approach to a New Triangular Rotor A Study on Wankel Rotary Piston Engine

三角转子发动机的研究