TIC的例句大全

Technical process study of tic/ 2618 composite prepared by XD method

用原位反应合成法制备TiC/2618复合材料的工艺过程研究

Consumerism and the Turn of Aes the tic Life

消费主义与审美生活转向

In order to make synthetic leather closer to natural leather in appearance and characteris-tics, it must be intimate the composition of natural leather.

为使合成革的外观和性能更接近天然皮革，必须要模仿天然皮革的组成结构。

Elevated temperature tensile behaviour of NiAl-TiC in situ composites

NiAl－TiC内生复合材料的高温拉伸行为

Fretting Wear Behaviour of TiC/ Ti ( C, N)/ TiN Multi-Layer Coatings at Elevated Temperature in Gross Slip Regime

TiC/Ti（C，N）/TiN复合涂层在滑移区的高温微动磨损特性

Proper additive Mg and rare earth can improve the hardness, wear-resisting property tensile-strength, elongation percentage of TiC/ Al, TiC/ Al-Si composite.

加入适量添加剂Mg和稀土CeO2使原位TiC／Al，TiC／Al-Si复合材料的硬武汉科技人学硕1：论义度、咐磨性、抗拉强度、延伸率得到很大的提高。

From three points of views, such as the service tariff, service selection and aiming mar-ket of the service of IN, the pa-per discusses the marketing tac-tics of the IN service.

并从智能网业务的资费、业务的选择以及业务的目标市场3个方面，探讨了智能网业务的营销策略。

The optimal reacting time is 3-5 min, and the formed TiC nucleus are most efficient to the refining effect of the Al-Ti-C master alloys.

TiC形成的最佳反应时间为3－5min，此时形成的TiC晶核最有效，制备的Al－Ti－C中间合金细化效果最佳。

Study of technology method of preparing tic 、 tin fine powder in planet ball-milling

行星球磨制备TiC、TiN微粉工艺方法的研究

Ti ( C, N)-based cermet was prepared from TiC, TiN fine powder with the size of 0.2 μ m by sintering in vacuum at ( 1 430 ℃) for 1 h.

由平均粒径为0.2μm的TiC，TiN细粉，经1430℃，1h真空烧结制备了Ti（C，N）基金属陶瓷。

The paper describes the good characteristic of Al2O3-TiC composite ( AG2 ceramic) tips and makes a comparison between the said tip and cemented carbide tip for cutting unworkable materials.

介绍了Al2O3－TiC复合陶瓷（即AG2陶瓷）刀片的优良特性，并在切削难加工材料方面，将其与硬质合金刀片进行了效果分析对比。

The Study of Deposition of TiC on the Electrode Tip Surface of Resistance Spot Welding by Vibrating Electric Sparking

点焊电极表面振动电火花熔敷TiC的研究

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM, EDX and XRD.

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

Microstructure and Formation Mechanism of TiC Reinforced Titanium Matrix Composite Layer by Laser Cladding

TiC增强钛基复合材料激光熔覆层显微组织及形成机理

Thus formed TiC during crystallization can increase the hardness, ( wearability,) thermal resistance and high-temperature intensity of bead welding metal, which can greatly lower the cost of bead welding rod.

可见，在结晶过程中形成的TiC提高了堆焊金属的硬度、耐磨性、耐热性和高温强度，可大大地降低堆焊焊条的成本。

After comprehensively surveying the minimum thermal stress, minimum ratio stress and stress state at the pure TiC side, the compositional distribution of TiC/ Ni_3Al system FGM is optimized.

在考虑热应力最小、比应力最小以及TiC侧应力状态等因素之后，对圆板状TiC／Ni3Al系梯度材料的组成分布进行了优化。

The thermal shock fatigue mechanisms of the ceram were discussed. The effects of TiC content on the thermal shock fatigue resistance were studied.

研究了Al2O3-TiC复合陶瓷的热震疲劳机制和TiC的添加量对其热震疲劳抗力的影响。

The thermal shock fatigue mechanisms of TiC/ Al_2O_3 composite were studied and the influence of different TiC starting powder size on the thermal shock fatigue resistance was discussed.

研究了TiC/Al2O3复合陶瓷的热震循环疲劳机制和TiC起始粉末粒径对热震循环疲劳抗力的影响。TiC起始粉末粒径的调整可以控制TiC/Al2O3复合陶瓷的晶粒大小。

The Thermal Shock and Fatigue Behaviors of Al_2O_3-TiC Composite Ceramic

Al2O3-TiC复合陶瓷的热震和热疲劳行为

This work in the thesis was undertaken to assess the thermal shock and thermal fatigue behavior of monolithic alumina and Al2O3-TiC composite ceramics.

本论文的工作就是评价纯Al2O3和Al2O3-TiC复合陶瓷的热震和热疲劳性能。